User manual FLYMO GARDENVAC 2500W TURBO

[. . . ] FO T IN AN nce O RT e use M P efor efere I er ad b for futur Re tain & re AT I O RM N For all customer enquiries or for replacement parts, contact:- 01325 300303 www. flymo. com eop. customer. services@electrolux. co. uk 1 Carton Contents adjustable handle trigger 2 handle knobs mode indicator 2 handle bolts Air inlets debris bag frame adjustable shoulder harness debris bag cutting lines instruction manual nozzle IMPORTANT !Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS ARE MISSING CONTACT:- Electrolux Outdoor Products Customer Service Department direct Telephone : 01325 300303, Fax : 01325 318193 Safety If not used properly this Gardenvac can be dangerous. The warnings and safety instructions must be followed to ensure reasonable safety and efficiency in using this product. [. . . ] Fit next hole on the plastic trim to next location point on bag frame. . . . until all holes on the plastic trim of the debris bag are securely located to bag frame. (C) · ENSURE THE DEBRIS BAG IS FITTED SECURELY TO THE BAG FRAME. To Fit the Cutting Line to the Cutting Head (D) · Switch off and disconnect from the mains electricity supply BEFORE removing or fitting the cutting line. · Handle the cutting line with care - sharp edges can cause injury. Place the cutting line into the slot in the cutting head and click into place as illustrated in Figure D. SEE PRODUCT RATING LABEL FOR MODEL DETAILS E 4 2 2 1 To Fit Assembled Debris Bag To Product (E) · · Switch off and disconnect from the mains electricity supply BEFORE REMOVING OR REPLACING the fully assembled debris bag. The cutting head and cutting line continue to rotate after your Gardenvac has been switched off. 2 IMPORTANT: Do not squeeze the trigger when fitting the debris bag (E1) 1. Lift handle towards product until bag latch locates and click into place. (E4) 3 1 debris fin F To Remove Debris Bag From Product (F) 1. Move bag frame forward. 1 4 G Assembly instructions H Fitting the Handle Bolt (G) 1. Place handle bolt into the location slot on the product and slide into place. (G). The handle can be adjusted by turning handle knobs 3 full turns anti-clockwise, moving handle to position required and re-securing handle as described in 2. Adjust as required to ensure the shoulder harness is in the most comfortable position. K. J Buckle K How to Use WARNING The use of eye protection is recommended. To prevent dust irritation, the wearing of a face-mask is recommended. IMPORTANT!: YOUR PRODUCT WILL NOT OPERATE UNTIL THE FULLY ASSEMBLED DEBRIS BAG AND FRAME ARE PROPERLY FITTED. BEFORE USE: ENSURE THERE ARE NO GAPS BETWEEN THE DEBRIS BAG AND THE PRODUCT. · These can be selected by moving the mode indicator to adjust the nozzle position for blow, vacuum or jet vacuum mode. · In vacuum and jet vacuum modes the product will shred leaves etc. L BLOW Position 1 - Blow Mode The Gardenvac will blow debris from patios, paths, driveways, lawns, bushes, borders etc. To stop release trigger. M VACUUM Position 2 - Vacuum Mode In this position your product will pick up leaves, paper, rubbish, cans etc. IMPORTANT: REMOVE NYLON LINE BEFORE VACUUMING CANS Using As A Vacuum 1. Position nozzle slightly above the debris, squeeze the trigger and move slowly back and forth. [. . . ] * This guarantee is additional to, and in no way diminishes the customers statutory rights. Failures due to the following are not covered, therefore it is important that you read the instructions contained in this Operator's Manual and understand how to operate and maintain your machine: Failures not covered by guarantee * Replacing Cutting Line. * Failures as a result of not using the product in accordance with the instructions and recommendations contained in this Operator's Manual. * The following items listed are considered as wearing parts and their life is dependent on regular maintenance and are, therefore not normally subject to a valid warranty claim: Cutting Line, Electric Mains cable, Debris Bag. [. . . ]