User manual JENSEN JTA-380 DATASHEET

[. . . ] This unit does not contain any parts that can be repaired by the user. The symbol for class II (Double insulation) DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding ­ type plug. [. . . ] Point the Remote Control at the SENSOR (IR) located on the front of the System. The functions of the remote buttons are the same as the corresponding controls on the main unit. The performance of the infrared SENSOR may be degraded causing unreliable operation if there is a strong ambient light source in the same room. The recommended effective distance for remote operation is about 10-15 feet. RADIO OPERATION 1. Slide the BAND Selector (11) to either AM, FM or FM ST (FM Stereo Mode). Rotate the TUNING CONTROL (10) until you reach the radio station you wish to listen to. To turn off the radio, Slide the FUNCTION Selector (12) to the "OFF" position. The LCD DISPLAY will go "off". FM STEREO RECEPTION " will With the BAND Selector (11) in the "FM ST" position, the FM Stereo Indicator " light up when listening to a strong station that is broadcasting in "Stereo". Slide the BAND Selector (11) to the FM position if the FM stereo reception is weak. The reception may improve, but the sound is now monaural (MONO). 6 TIPS FOR BEST RECEPTION AM ­ The AM antenna is located inside the cabinet of the main unit. If AM reception is weak, change the position of cabinet until the internal antenna picks up the strongest AM signal. To start recording again, press the RECORD Button (17) again and follow step #2 above. 7. PLEASE NOTE : If you want to encode an entire side of a record and have seperate MP3 files for each track, you must manually press the STOP/USB/SD Button (15) at the end of each track and then press the RECORD Button (17) again to start recording the next track. If you do not manually Stop and Start the recording process after each track, you will end up with one large MP3 file that will have all the songs from the side of the record playing one after the other. 8 USB / CARD OPERATION The following tasks can be accomplished by either using the controls on the REMOTE Control or those which have similar function markings on the JTA-380 main unit. indicates that a task can only be performed using the controls on JTA-380. Select the USB / CARD function mode by setting the Function selector (12) to "USB/CARD". Insert either a USB flash drive into the USB PORT (22) or an SD/MMC Memory Card into the SD/MMC Slot (20). Press and hold the STOP/USB/CARD Button (3) for 2 seconds to switch between USB and CARD modes if necessary. The total number of tracks on the USB or SD/MMC card will be displayed and playback will automatically start from the first track depending which mode you have chosen (USB or CARD). NOTE: i. Press the or Buttons (4, 5) to select your desired track to be stored in the program. Press the MODE button (14) to confirmed when track No. 5 flashed in the Display. The first program selection is now stored in the program memory. the first selected program and flash together with `PROG' to prompt for another input. Repeat points 2 and 3 to enter the desired tracks up to max 32 selections. [. . . ] The chosen track, `005', will appear and blink in the Display to prompt for confirmation. In case you want to cancel the delete function just briefly press the STOP Button. 3. `DEL' will appear steadily in the Display for few seconds and then the Display will resume to USB/Card playback stop mode with the total track number deducted by 1. Original 38 Files After Deleting track 5 4. Repeat 1-3 above to delete more tracks as desired. LINE OUT OPERATION (OPTIONAL) For better playback sound, you can connect the JTA-380 to an external Audio Amplifier via the RCA LINE OUT JACKS located at the back panel. [. . . ]