User manual JENSEN VOYAGER JCDWIN

[. . . ] NOTE: CD-R and CD-RW discs will not play unless the recording session is closed and the CD is finalized. Audio CD RECORDABLE REWRITABLE DISC NOTES Compatible Disc Types Table 1: General Disc Information Disc Type Logo Diameter/ Playable Sides 12 cm single side Playback Time 74 minutes Disc Maintenance · A dirty or defective disc may cause sound dropouts while playing. Before playing, wipe the disc using a clean cloth, working from the center hole towards the outside edge. Never use benzene, thinners, cleaning fluids, anti-static liquids or any other solvent. Insert label side up. Do not bend. Never touch the under side of the disc. Wipe clean from the center to the edge. · · · Be sure to use only round CDs for this unit and do not use any special shape CDs. [. . . ] Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward as necessary to firmly secure the sleeve to the dashboard. Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve. Follow the wiring diagram carefully and make certain all connections are secure and insulated with crimp connectors or electrical tape to ensure proper operation. After completing the wiring connections, turn the unit on to confirm operation (vehicle ignition switch must be on). If the unit does not operate, recheck all wiring until the Removing the Unit To remove the radio after installation, insert the removal keys straight back until they click, and then pull the radio out. If removal keys are inserted at an angle, they will not lock properly to release the unit. Removal Key Reconnect the Battery When wiring is complete, reconnect the battery negative terminal. 2. 3. 4. 6. 3 JCDWIN WIRING A- A SHOWN FROM PIN VIEW 15A FUSE A-A Wire Connector ACCESSORY/IGNITION (+) Connect to existing radio accessory fuse or +12 VDC switched power source. If not used, tape bare end of wire. MEMORY/BATTERY (+) Connect to battery or 12 volt power source that is always live. GROUND Connect to ground terminal or clean, unpainted metal part of chassis. 4 JCDWIN BASIC OPERATION 1 12 7 3. Press MODE again to cancel Aux In mode and return to previous mode. Reset 6 5 21 4 19 3 2 After releasing the control panel, use a pencil or any non-metallic object to press and hold the RESET button (17) for five seconds to reset the main unit. The reset button should be activated for the following reasons: · · · initial installation of the unit when all wiring is completed function buttons do not operate error symbol on the display 9 17 10 13 Audio Menu Press the AUDIO button (4) on the control panel (or the S button on the remote control) to access the Audio Menu. You can navigate through the Audio Menu items by pressing the AUDIO (or S) button repeatedly. Once the desired menu item appears on the display, adjust that option by turning the AUDIO control (or pressing the VOL /\ or VOL \/ buttons (24) on the remote control) the within 5 seconds. The unit will automatically exit the Audio Menu after five seconds of inactivity. Volume Level Use the button to adjust the Volume level from "00" (lowest) to "100" (highest). Bass Level 1 VOL S 11 14 15 22 16 8 18 20 Power On/Off ( ) Press the button (1) to turn the unit ON or OFF. Volume Control To increase the volume, turn the AUDIO control (4) clockwise. If using the remote control, press the VOL /\ or VOL \/ button (24) to adjust the volume. When the volume is adjusted, the volume level is shown on the display panel as a number ranging from 00 (lowest) to 100 (highest). 4 Use the button to adjust the Bass level range from "-10" to "+10". Treble Level Use the button to adjust the Treble level range from "-10" to "+10". UP 22 5 23 16 6 11 10 14 Use the button to adjust the Balance between the right and left speakers from "10L" (full left) to "10R" (full right). [. . . ] Intro Scan (2/INT) Press the 2/INT button (10) on the control panel to play the first 10 seconds of each track sequentially. Press 2/INT again to stop Intro Scan and resume normal play at the current track. Repeat Play (3/RPT) Press the 3/RPT button (11) during disc play to repeat play the current track. Random Play (4/SHF) Press the 4/SHF button (12) on the control panel during disc play to play all tracks on a CD in random, shuffled order. [. . . ]