User manual JVC VN-900
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual JVC VN-900. We hope that this JVC VN-900 user guide will be useful to you.
Manual abstract: user guide JVC VN-900
Detailed instructions for use are in the User's Guide.
[. . . ] Do not use attachments not recommended by the appliance manufacturer as they may cause hazards. Do not use this appliance near water - for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc. The appliance may fall, causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart or stand recommended by the manufacturer, or sold with the appliance. [. . . ] The light will appear blinking when troubles occur during startup and the error details will be displayed in CH1-CH4. CH1 CH2 CH3 CH4 Error Description A device with the same IP address as VN-900 is detected. The normal display will be restored upon input of video signals.
G [O. L] Overload Lamp Displays the processing load of VN-900. This light is turned on when the processing load of VN-900 is too heavy. I [CH1] Video 1 Channel Lamp Displays the image transmission status of VN-900. J [CH2] Video 2 Channel Lamp Displays the image transmission status of VN-900. K [CH3] Video 3 Channel Lamp Displays the image transmission status of VN-900. L [CH4] Video 4 Channel Lamp Displays the image transmission status of VN-900. Turns off when there is no transmission.
Light OFF
Light OFF
Light OFF
Light ON
Light OFF
Light OFF
Light ON
Light OFF
F [ALM] Alarm Lamp Displays alarm input to VN-900. Lights up when there are changes in the alarm input or when motion is detected. The light will turn off automatically after 5 seconds.
6
[Back]
M
AUDIO VIDEO INPUT
RS
CONTROL COM1 SERVICE OUTPUT
T
W
ALARM
RS-232C RS-485
IN
1CH
2CH
COM OUT
1
2
PUSH
3
4
G
INPUT
OUT
3CH
4CH
COM2
10BASE-T/100BASE-TX
RESET
DC 5V
N
O
P
Q
U
VX
M [AUDIO IN] terminal (RCA pin) For input of audio signals. Fasten each end using 1 M3 screw and 2 M4 screws that are supplied with the rack mount bracket. )
2. Fasten to the rack using the M5 screws supplied with the rack mount bracket
(2 M5 screws at each end)
2.
1.
PO
WE
R LIN K 100M
FD X /CO L
ST
S
AL
M
O. L
AU
D
CH 1
CH 2
CH 3
CH 4
1.
2.
In case of 2 units. Mount the joint bracket to the connecting face of the unit
(Remove 3 screws from VN-900. Connect with 3 M3 screws that are supplied with the rack mount bracket. )
2. Fasten the 4 locations (top and bottom) using the M3 screws supplied with the rack mount bracket
(For joining the left and right units)
3. Mount the side bracket on both left and right
(Remove 1 screw from each end of VN-900. Fasten each end using 1 M3 screw and 2 M4 screws that are supplied with the rack mount bracket. )
4. Fasten to the rack using the M5 screws supplied with the rack mount bracket
(2 M5 screws at each end)
2. 4.
POW ER LINK 100 M FDX /CO L
STS ALM O. L AUD CH1 CH2
CH3
CH4
1.
POW ER LINK 100 M FDX /CO L
STS ALM O. L AUD CH1 CH2 CH3 CH4
3.
2.
10
4.
IP Address Setting
There are 2 ways to set the IP address of VN-900. (A) Assigning IP address to VN-900 from the DHCP server (B) Assigning a static IP address to VN-900 upon turning off the DHCP client function of VN-900
(A) Assigning IP Address from the DHCP Server
The DHCP client function is set to ON in the factory settings of VN-900. By assigning an IP address from the DHCP server, VN-900 can be connected to the network without manual setting of IP address. [. . . ] https://192. 168. 0. 2/e4viewer/e4monitor. html
A Enter the URL of built-in viewer of the unit. (In factory setting,
https://192. 168. 0. 2/e4viewer/e4monitor. html is the URL when there is no DHCP server. )
B Click AGoB.
MEMO
Direct specification of the IP address may not be possible when a proxy server is used for Internet access. When a security warning screen appears, click the AOKB button to proceed.
2.
Enter the user name and password.
A Enter user name of administrator. The viewer will be installed and launched.
19
(3) Operating the viewer
"Image Selection" Use the ACH1-CH4B buttons to select the video channel to display. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE JVC VN-900
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual JVC VN-900 will begin.