Detailed instructions for use are in the User's Guide.
[. . . ] : Inbetriebnahme am:
Prüfung durchgeführt am: Befund:
Unterschrift Prüfung durchgeführt am: Befund:
Unterschrift Prüfung durchgeführt am: Befund:
Unterschrift Prüfung durchgeführt am: Befund:
Unterschrift
16
DE
- 14
Please read and comply with these original instructions prior toEnglish the initial operation of your appliance and store them for later use or subsequent owners. Before first start-up it is definitely necessary to read the safety indications Nr. Safety instructions
General
Mishandling or misuse can prove to be hazardous to the operator and other persons through – high water pressure, – hot water, – hot exhausts (not HDS-C 8/15-E), – high electrical voltage, – detergents. To avoid danger to persons, animals and property before the first operation of the system, read: – the operation instructions – all safety notices – according to the national requirements of each country – that safety notices included in the cleaning agents used (normally on top of the package stated). [. . . ] Oil quantity of HP pump Oil grade Values determined as per EN 60355-2-79 Hand-arm vibration value Hand spraygun Spray lance Uncertainty K Sound pressure level LpA Sound power level LWA + Uncertainty KWA m/s2 m/s
2
SB-HDS 9/15
HDS-C 8/15-E
V/Hz kW (max. 180
29 – – –
mm mm mm kg
1040 727 1360 245
l
25 Fuel oil EL or Diesel
– – 55 19 0, 75 0, 55 Hypoid SAE 90
l l l 0, 75 15W40
– –
Hypoid SAE 90
<2, 5 <2, 5 1 54 71 71 88 54 71
m/s2 dB(A) dB(A)
22
EN
-6
Maintenance and care
System overview
1 Fuel tank* 2 Fuel filter and fuel pump* 3 Oil tank 4 Burner with continuous heater* 5 Photovoltaic cell for flame monitoring* 6 Exhaust pipe* 7 Container for softener (RM 110) 8 Coin verification unit (optional) 9 Coin container (optional) 10 High pressure pump 11 high pressure hose 12 Fan heater 13 Cleaning agent container * only HDS-C 7/11, HDS-C 9/15
Maintenance instructions
The bases of a safe operating of the equipment is thr regularly maintenance according to the following maintenance plan. Use only original parts of the manufacturer or part suggessted by him, such as – parts and wearing parts, – accessories parts, – operating materials, – cleaning agents. During all tasks Turn off the water supply; close the fresh water tap, First switch-on in voltage-less state, switch off the emergency stop switch in the building and secure it against being switched on again. operator Performances containing the notice "operator" may only be performed by instructed individualls, who are able to operate and service high pressure equipment. Maintenance Performances with the notice "maintenance" may only be performed by the Kärcher- Maintenance-Mechanics. Maintenance contract In order to guarantee a reliable operation og the equipment, we success, you signed a maintenance agreement. Danger of injury because of possible damaged parts of the high pressure jet, danger of burns because of hot equipment parts. When working, while the equipment is open take special care, and obey all safty notices!The following parts are possible to be hotter than 50 °C: – Exhaust pipe and exhaust opening (only HDS-C 7/11, HDS-C 9/15) – Burner with continuous heater (only HDS-C 7/11, HDS-C 9/15) – cylinder head of the high pressure pump – high pressure hose
EN
-7
23
Maintenance schedule
Time daily Activity Visible inspection of the high pressure hoses Check warning boards at the washing place Check the unit for leaks Performance By whom
Check high pressure hoses for mechanical damages such as scraping, vis- Operator ible hose duck, bends, porous and cracked rubber. Check whether the warning boards for the users are available and legible. Inform Customer Service if there is oil under the high pressure pump, if more than 3 drops of water drop out of the high pressure pump when the pump is running. Operator
Check fill level of detergent tank Empty the coin container
Operator Operator Operator Operator
Only HDS-C 7/11, HDS-C 9/ Check filling level, refill if necessary. 15: Check fill level of fuel tank Everyday under frost conditions After 40 operating hours or once a week After 80 operating hours or once every two weeks After 160 operating hours or once a month Check frost protection devices Is the hot air blower working?Check oil level of the high pressure pump Check oil level Check filling level of softener liquid Clean and maintain housing
The oil level must lie between the MIN and MAX markings; else refill. Operator Operator Operator
Clean the housing thoroughly from inside and outside. Operator Take care of the stainless steel casing using steel cleaner (order no. Clean detergent filter in the detergent container
Remove filter and rinse it thoroughly with hot water. Operator Operator Operator Operator Customer Service Customer Service Customer Service
Clean sieve in the water short- See Maintenance tasks age safe guard. Lubricate the door hinges Door locks Lubricate the hinges with grease (order no. After 250 operating hours or once every six months After 500 operating hours or once a year
Check pump head Only HDS-C 7/11, HDS-C 9/ 15: Adjust ignition electrodes, replace if required Check the high pressure pump thoroughly Oil change in high pressure pump Only HDS-C 7/11, HDS-C 9/ 15: Desoot the heating coil, adjust burner Only HDS-C 7/11, HDS-C 9/ 15: Decalcify the heating coil Only HDS-C 7/11, HDS-C 9/ 15: Clean the fuel container See Maintenance tasks See Maintenance tasks See Maintenance tasks
Operator Customer Service Trained operator Operator
24
EN
-8
Maintenance Works
Oil change
ƽ Danger
Risk of burns due to hot oil or hot parts of the plant. Note Please dispose off used oil only in the collection points provided for them. [. . . ] 18 °dH,
Aligning the unit and installing it
Line up the equipment on the level area. hydrocarbons Chloride Calcium Total hardness Iron Manganese Copper Sulphate Active chloride free of bad odours For connection values refer to technical specifications. σ Insert the inlet hose from the bottom through the plant opening and connect it. σ Determining the hardness of tap water: – through the public water supply works, – Using hardness testing set, order no. [. . . ]