User manual KARCHER SDP 14000 IP LEVEL SENSOR
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual KARCHER SDP 14000 IP LEVEL SENSOR. We hope that this KARCHER SDP 14000 IP LEVEL SENSOR user guide will be useful to you.
Manual abstract: user guide KARCHER SDP 14000 IP LEVEL SENSOR
Detailed instructions for use are in the User's Guide.
[. . . ] Notes about the ingredients (REACH) You will find current information about the ingredients at: www. Com/REACH
EN – 1
13
Warranty
The warranty terms published by the relevant sales company are applicable in each country. We will repair potential failures of your appliance within the warranty period free of charge, provided that such failure is caused by faulty material or defects in manufacturing. [. . . ] EN – 2
Prerequisites for the appliance's stability
Caution Create stability for the appliance prior to all work on or with the appliance to prevent accidents or damage. The stability of the appliance is warranted when it is placed onto an even surface. Operation
Description of the Appliance
1 2 3 4 5 6 7 8 Power cord with plug Level switch (IQ Level Sensor) Ventilation button Carrying handle Hose connection 1“ (25. 7 mm) Flat seal Backflow valve Cable connector
Preparing the Appliance
Please follow the safety instructions before start-up!If you would like to prevent the water that is standing in the hose or above the pump after the pump has been turned off, we recommend that you use the included backflow valve. Illustration Unfold the folding legs if you are working without pre-filter (only SCP 12000 ). Illustration Set the IQ Level Sensor to the desired switching height. The IQ Level Sensor can be removed from the guide rail toward the top and placed separately if necessary. Illustration Place the pump on a level, stabile surface in the liquid to be transported, ensure that it is standing firmly or immerse it using a rope tied to the handle. The suction area should not be blocked fully or partially through the impurities. Illustration When installing the pump, you must make sure that the pump can be submerged up to the max. The flow height indicates the height difference between the water level and water exit at the end of the flow hose. This must be observed throughout the entire pump run, as the flow height will increase with a decreasing water level (due to the pumping). EN – 3
15
Operation
The fluid level must be minimum 3 cm (SCP 1200) or 8 cm (SDP 14000) for the pump to suck in automaticallt. If the liquid level is less than 4 cm (only SCP 12000), proceed according to instructions in the chapter of flat suction. The pump switches off automatically after 10 to 60 seconds (depending on the ambient conditions) when the fluid level falls below the IQ Level Sensor. The pump automatically conducts the adaptation to the necessary trail time/ pump time. If the mains plug is pulled prior to the 24 hour time period, or after the 24 hours have elapsed, the pump will automatically set the trail time/pump time to the set value of 10 seconds. [. . . ] Fault Pumping capacity is reducing Pumping capacity too low Cause Suction area blocked Remedy Pull out the mains plug and clean the suction area
The pumping capacity de- Keep max. Air in the pump Press the ventilation button or plug in/ disconnect the mains plug of the pump a few times till the fluid gets sucked. Pull out the mains plug and clean the suction area Immerse, whenever possible, the pump deeper into the liquid or, in case of SCP 12000, proceed according to instructions in the chapter on flat suction. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE KARCHER SDP 14000 IP LEVEL SENSOR
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual KARCHER SDP 14000 IP LEVEL SENSOR will begin.