User manual KEYENCE FS-V22
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual KEYENCE FS-V22. We hope that this KEYENCE FS-V22 user guide will be useful to you.
Manual abstract: user guide KEYENCE FS-V22
Detailed instructions for use are in the User's Guide.
[. . . ] · Accessories Instruction End units (x2) Expansion Sticker (x1) manual (x1)
Note:If a thin fiber unit is used, an adapter provided with the thin fiber unit will be required. Unless the right adapter is connected, the thin fiber unit will not detect targets correctly.
Cable outer dia. ø1. 3 ø1. 0
Adapter Adapter A Adapter B
Appearance
Slide the unit to the right to remove it.
· To connect the coaxial reflective type fiber unit to the amplifier, connect the single-core fiber to the transmitter side, and connect the multiplecore fiber to the receiver side.
2. Part Names
Fiber lock lever Operation indicator* Set button Digital monitor Manual button Preset value (PV) green indicator Current value (CV) red indicator
Single-core fiber Multi-core fiber
Transmitter
Receiver
· To remove the amplifiers added, take the steps opposite to the mounting procedure. [. . . ] Then press the set button for a minimum of three seconds.
Workpiece Front edge 3 s min. Selecting Output
The display will be lit when the workpiece is detected.
Either light-ON mode or dark-ON mode is selectable.
Press the mode button.
* If there is extremely little difference in sensitivity between the sensing values, the display will flash on completion of tuning. G Maximum Sensitivity Setting If the sensing performance of the sensor drops due to dust or dirt, set the sensitivity of the sensor to maximum. 1) Press the set button without a workpiece if the fiber unit is a reflective model. Press the set button with a workpiece if the fiber unit is a through-beam model. In both cases, press the set button for a minimum of three seconds.
"Reflective model" "Through-beam model" 3 s min. Then the PV will be displayed.
* If the sensing distance is insufficient, make sensitivity settings in the sensor in two-point tuning mode.
Workpiece
The PV will appear when the settings are completed.
The display indicates that the sensor is in dark-ON mode. The CV will be displayed if no buttons are operated for approximately five seconds.
Press the manual button within five seconds after pressing the mode button .
· Take the same steps to set the sensor to light-ON mode again.
8. User-friendly Functions
G Access Mode Selection Two modes are available to the display of values and menu items. EASY FULL
· The mode is set to EASY before shipping.
2
q Display Selection (Access Mode: EASY)
PV CV
q Menu Selection (Access Mode: FULL)
Press Press Press
Access mode selection
Press the mode button 3 s min
Normal operation use Power mode selection Press FINE Used if the sensing distance is insufficient TURBO while the sensor is in fine mode. Used if the sensing environment is SUPER TURBO bad due to dust or other obstacles. Used if the incident is insufficient while ULTRA TURBO the sensor is in SUPER TURBO mode. Used to detect delicate differences HIGH RESO- within a short sensing distance. LUTION Timer OFF (for normal operation use) OFF-delay timer ON-delay timer One-shot timer
Excess gain
CV
Output Power status mode status · The current value will be displayed if no keys are operated for approximately 30 s. · If the timer function is set, the output status with power mode and the timer mode with set time will be displayed alternately.
· The CV is displayed in percent based on the PV.
Select Press
q Display Selection (Access Mode: FULL)
PV CV
Timer function setting Select Press
Press
Press
Other than
Excess gain
Output status CV
Power mode status Press
Power mode , S-APC mode setting
Press Other than Power mode ,
Timer adjustments Timer adjustment range 1~30ms 1-ms increments 30~50ms 2-ms increments 50~200ms 10-ms increments 200~500ms 50-ms increments * A maximum error of ±10% of the PV. OFF (for normal operation use) Used to detect sensing objects highly precisely under clean environments.
Press Peak excess gain Bottom excess gain Press Press Peak value Bottom value
Select Press Edge detection mode selection Select
LED bar indicator
CV
q Menu Selection (Access Mode: EASY)
Power save function setting
Press
OFF (for normal operation use) Rising edge Falling edge OFF (for normal operation use) ECO half ECO all
Press the mode button 3 s min Access mode selection Press Power mode selection Press manual button to select Press Timer function setting Press manual button to select Press
Select
Normal FINE operation use Used if the sensing TURBO distance is insufficient while the sensor is in fine mode. Used if the sensing SUPER environment is bad TURBO due to dust or other obstacles. Timer OFF (for normal operation use) OFF-delay timer ON-delay timer One-shot timer
Power mode
Press Other than Power mode
Shift function setting
Select Press
OFF (for normal operation use) Shift ON
Shift value adjustment Press Shift value CV
Other than Press to manual button to make timer adjustments * For timer values, refer to the corresponding table under FULL mode.
Press
Sensitivity Settings in Edge Detection Mode The sensitivity of the sensor will be set to maximum by pressing the while the sensor is in edge detection mode. [. . . ] · Due to the individual dispersion of characteristics and the difference in fiber unit model, the maximum sensing distance or displayed value of all the units are not the same. · If the sensor is used in S-APC mode for a long time, the LED indicators will be imposed with a heavy load. In that case, the sensor will be automatically set to ACC mode where the current consumption of the sensor for light emission will be constant, and "END APC" will be displayed. PHONE: 6392-1011 FAX: 6392-5055 KEYENCE (MALAYSIA) SDN BHD PHONE: 03-252-2211 FAX: 03-252-2131 4 KEYENCE TAIWAN CO. , LTD. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE KEYENCE FS-V22
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual KEYENCE FS-V22 will begin.