User manual KYOCERA FS-1000+
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual KYOCERA FS-1000+. We hope that this KYOCERA FS-1000+ user guide will be useful to you.
Manual abstract: user guide KYOCERA FS-1000+
Detailed instructions for use are in the User's Guide.
[. . . ] Table of Contents
Page Printer
User's Manual
Caution
NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION.
Notice on Software
SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER'S EMULATION MODE. The emulation mode can be changed by following the procedures described in Chapter 1.
Notice
The information in this manual is subject to change without notification. The user is asked to excuse any technical inaccuracies or typographical errors in the present edition. No responsibility is assumed if accidents occur while the user is following the instructions in this manual. [. . . ] The total host buffer size can be between 5 kB and the printer's free memory size.
1
Click the MENU button on the start-up screen.
2
The Menu dialog box is displayed. Using the radio buttons on the right, select either Fix or Auto.
Memory Host buffer mode
1-45
Other Settings
3
Click Host buffer size. The total host buffer size is increased or decreased in 1 kB increments. You can input the host buffer size directly in the number field.
Host buffer size
4
Note
Turn the printer's power off and on again. The setting becomes effective when you restart the printer.
We recommend that you leave the default settings for Host buffer mode and Host buffer size unchanged.
1-46
Other Settings
1. 6. 5
Adding an Asset Number to the Printer
You can add an asset number to the printer. The asset number can only be defined when your printer is connected to a network, and is stored by the printer. The name and explanation are stored in the Remote Operation Panel utility.
1
Click the MENU button on the start-up screen.
2
The Menu dialog box appears. Double click on General and then on User defined setting.
General User defined setting
3
Click the Asset number, and enter the asset number for that item in the text box on the right side of the screen.
Type the asset number Asset number
4
After making the settings, click the OK button to return to the startup screen. The settings are changed.
1-47
Other Settings
1. 6. 6
Displaying the Resource List
When the printer is connected to a network, you can display the printer's resource list, including fonts, programs, macros, and/or host data.
1
Click the Resource tab.
Resource tab
2
Click the check box that corresponds to the resource you want to display.
Font check box
3
Click the Update button. A list of all items for that resource are displayed.
Update
4
After confirming, click the OK button to return to the start-up screen.
1-48
Other Settings
1. 6. 7
Sending PRESCRIBE Commands to the Printer
You can send commands to the printer in Kyocera Mita's PRESCRIBE printer language by broadcasting. You can also use this menu to confirm the printer's internal settings. For details on PRESCRIBE commands and FRPO settings, refer to the Programming Manual provided on the CD-ROM supplied with the printer.
Note
1
Click the MENU button on the start-up screen.
2
The Menu dialog box appears. Click Broadcast.
Broadcast
1-49
Other Settings
3
Click Broadcast to display the dialog box shown below.
Broadcast
FRPO
Broadcast To send PRESCRIBE commands to the printer, enter the command in the Broadcast text box. FRPO FRPO is a PRESCRIBE command that permanently changes the printer's internal parameters. Each parameter is represented by two letters, such as R4 for default paper source, succeeded by FRPO, then followed by a value. For example, FRPO R4, 1; means that the default paper source (R4) is the printer's cassette (1). To confirm the current value for an FRPO parameter:
1 2 1 2 3
Enter the parameter (for example R4) in FRPO. The current value is shown in Value.
To change the value for an FRPO parameter: Follow the above procedure to display the current value in Value. For example, to change the default paper source to the MP Tray in the above example, enter 0 instead of 1 in Value. The value is changed.
1-50
Chapter 2
Printer Driver
2
This chapter describes how to perform basic print operations using the printer driver, such as setting the paper size and selecting a paper source. About the printer driver The Kyocera Mita Digital Library CD-ROM supplied with this printer contains the printer drivers for Windows and Macintosh computers. By installing this printer driver on your computer, you can print from Windows and Macintosh applications. [. . . ] To use this, the KPDL2 Upgrade Kit (PK-6) must be installed on your printer.
Kyocera Mita Digital Library
This is contained on the CD-ROM supplied with the printer. The contents of the CD-ROM include manuals, printer drivers, and various utilities.
Face-up tray
This is located at the rear of the printer. Select paper output to the face-up tray when printing on postcards, envelopes, or labels.
Kyocera Mita PrintMonitor
This is a network management tool that can be used with the printer. You can view information for printers connected to the network using SNMP commands. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE KYOCERA FS-1000+
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual KYOCERA FS-1000+ will begin.