User manual KYOCERA FS-1010
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual KYOCERA FS-1010. We hope that this KYOCERA FS-1010 user guide will be useful to you.
You may also download the following manuals related to this product:
KYOCERA FS-1010 (3747 ko)
KYOCERA FS-1010 (2853 ko)
KYOCERA FS-1010 (3192 ko)
KYOCERA FS-1010 MANUAL 2 (10396 ko)
KYOCERA FS-1010 DATASHEET (365 ko)
KYOCERA FS-1010 INSTALLATIONSANLEITUNG (3747 ko)
KYOCERA FS-1010 MANUAL 2 (7734 ko)
KYOCERA FS-1010 KMNET VIEWER (855 ko)
KYOCERA FS-1010 INSTALLATION (1213 ko)
KYOCERA FS-1010 PRESCRIBE COMMANDS (5165 ko)
KYOCERA FS-1010 TECHNICAL REFERENCE (9320 ko)
KYOCERA FS-1010 FILE MANAGEMENT UTILITY (224 ko)
KYOCERA FS-1010 PRESCRIBE COMMANDS REFERENCE (REV.4.9) (4876 ko)
Manual abstract: user guide KYOCERA FS-1010
Detailed instructions for use are in the User's Guide.
[. . . ] Table of Contents
Page Printer
Operation Guide
Caution
NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION.
Notice on Software
SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER'S EMULATION MODE. The emulation mode can be changed by following the procedures described in Chapter 1 .
Notice
The information in this manual is subject to change without notification. The user is asked to excuse any technical inaccuracies or typographical errors in the present edition. No responsibility is assumed if accidents occur while the user is following the instructions in this manual. [. . . ] To release the page protect mode, send the following command to the printer from the KM-NET for Clients after this error occurs: !R!FRPO R5, 1; EXIT;
KPDL Error Press GO
MemoryCard err## Press GO
Memory overflow Press GO Print overrun Press GO
RAM DISK error ## Press GO
Check the error code displayed in ## and refer to the appropriate description below. Expand printer memory.
(Continued on next page)
3-11
Indicators
Indicator
KM-NET for Clients display Memory card err20
Corrective Action The printer has halted because you attempted to insert/ remove a memory card into/from the printer slot while the printer power is on. Make sure to turn the printer power off before inserting/ removing a memory card.
(No indication patterns available)
Format error Memory card
This message appears when the printer is in the ready state and the memory card is not formatted, and therefore cannot be read or written. Format the memory card.
3-12
Indicators
3. 3. 4
Normal Indicator Display
The following displays appear during normal printer operation.
Indicator KM-NET for Clients display Cancelling data Description Data inside the printer is being canceled. The indicators light in sequence from the top, then go off in sequence from the bottom. When the printer is switched on for the first time after the toner container is installed, (Adding toner) also appears. When the printer is switched on for the first time after the toner container is installed, (Adding toner) also appears.
Please wait
Processing
The printer is receiving data.
Processing Waiting
The printer is processing data. The printer is waiting for the end-of-job command before printing the last page. The printer is ready to print.
Form Feed Timeout Ready
The printer is offline. The indicator flashes at 5-second intervals and all other indicators go off. The printer wakes from Sleep mode whenever a key on the operator panel is pressed, the cover is opened or closed, or data is received. (You can set the amount of time before the printer enters sleep mode from the KM-NET for Clients utility. )
3-13
Correcting a Paper Jam
3. 4
Correcting a Paper Jam
This section describes how to remove paper when it jams in the printer. The printer will stop whenever paper jams in the printer or paper is not fed from a paper cassette. The printer will go offline and (paper jam) indicator will light in the operator panel. When a jam occurs, check the points indicated in the following and clear the jam as indicated. If paper jams occur frequently, try using a different type of paper, replace with paper from another ream, turn the stack of paper over, or turn the paper the other way around. Also, look for tiny pieces of paper that may have been torn apart and overlooked when the jammed paper was removed. If you cannot solve the problem by changing the paper, there may be a problem with the printer. Torn pieces of paper are difficult to remove and may be easily overlooked, deterring the jam recovery. Depending on where the jam occurred, the printer may or may not reprint the jammed page.
·
3. 4. 1
Jam at the Face-down and Face-up Trays
When paper is fed part way out into the tray, pull the paper out the rest of the way by hand. The printer then automatically warms up and resumes printing.
Face-up Tray
3-14
Correcting a Paper Jam
3. 4. 2
Jam at the Paper Cassette
Pull out the paper cassette and remove any partially fed paper, then reclose the paper cassette. [. . . ] The printer has one expansion slot, and you can install a 16 MB, 32 MB, 64 MB, or 128 MB DIMM (Dual Inline Memory Module). Contact your Kyocera Mita dealer to purchase the DIMM that is best suited for use with this printer.
KM-NET VIEWER
This is a network management tool that can be used with the printer. You can view information for printers connected to the network using SNMP commands. KM-NET VIEWER is contained on the Kyocera Mita Software Library CD-ROM supplied with the printer.
Face-up tray
This is located at the rear of the printer. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE KYOCERA FS-1010
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual KYOCERA FS-1010 will begin.