User manual KYOCERA FS-1350DN COMMAND CENTER

[. . . ] OPERATION GUIDE COMMAND FS-1100 CENTER FS-1300D Legal and General Information Notice Unauthorized reproduction of all or part of this guide is prohibited. Kyocera Mita cannot be held liable for any problems arising from the use of this product, regardless of the information herein. Regarding Trademarks KYOCERA, KYOCERA MITA, ECOSYS and PRESCRIBE are registered trademarks of Kyocera Corporation. KPDL and KIR (Kyocera Image Refinement) are trademarks of Kyocera Corporation. [. . . ] Addition from the Address Book There are two types of address book: address book contacts and address book groups. In address book Operation Guide 25 COMMAND CENTER Pages groups, each entry has multiple addresses. When an address of a group is added, faxes are forwarded to all addresses registered in the group. Before adding an address from an address book, you have to register the address in the address book. For how to register an address in an address book, refer to Basic > Defaults > Address Book > Contacts on page 10 or Basic > Defaults > Address Book > Groups on page 11. Put a check mark in the check box for the address or group you want to add to the destinations. 4. Put a check mark in the check box for the destination you want to delete from the Destination List. After confirming the settings, click Submit. FAX / i-FAX > FAX > Defaults The table below provides a summary of the items displayed on the FAX / i-FAX > FAX > Defaults page. Item Local FAX Number (Port 1/ 2) FAX Line Description Specifies your FAX system number. Sets the type of phone line to correspond to the type of telephone service that you are using. Be sure that the type of phone line you select is correct because, if the setting is incorrect, dialing will be impossible. Specifies your FAX system ID. Local FAX ID 26 KYOCERA COMMAND CENTER COMMAND CENTER Pages Item Speaker Volume Description Sets the volume of the internal speaker that allows you to listen to conditions on the telephone line when the [OnHook] key was pressed. Sets the volume of the internal speaker that allows you to listen to conditions on the telephone line when the [OnHook] key was not pressed. The choices are Off and levels 1, 2 or 3. Monitor Volume FAX / i-FAX > FAX > Transmit The table below provides a summary of the items displayed on the Transmit page. Item TTI TTI Position Description Selects On or Off whether to send the TTI (Transmit Terminal Identifier) information to other party. Selects the position of the TTI to be printed on the transmitted documents. FAX / i-FAX > FAX > Receive The table below provides a summary of the items displayed on the Receive page. Remote switching allows you to initiate FAX reception from a telephone connected to the FAX system. Sets the encryption key number to be used for encrypted communication. This is not displayed on European models. DRD Pattern Remote Switching Dial Number Encryption Key No. Reception Port Number of Rings (Normal) Number of Rings (TAD) Number of Rings (FAX/TEL) Operation Guide 27 COMMAND CENTER Pages FAX / i-FAX > FAX > FAX Restrictions > General The table below provides a summary of the items displayed on the FAX Restrictions > General page. Item Transmit Restriction Receive Restriction Description Selects the transmitting restriction between Off and Use Permit List + Address Book. Selects the receiving restriction between Off, Use Permit List + Address Book, and Use Reject List. FAX / i-FAX > FAX > FAX Restrictions > Permit Number List The table below provides a summary of the items displayed on the Permit Number List page. Item Add Description Clicking Add will display the Permit Number List - Add page. [. . . ] Specifies whether the lifetime is measured by time or by time and data size. Hash Encryption PFS DiffieHellman Group Lifetime Measurement Lifetime (Time)/ Lifetime (Data Size) IP Version IP Address (IPv4) Specifies the lifetime of an IPSec SA. Lifetime Measurement allows you to select whether to use time or data size to specify the lifetime. When you select Time & Data Size, an SA is disabled and updated when either the time or data size of the SA exceeds the specified value. Specifies the IPv4 addresses of the hosts or network with which the print system is connecting via IPSec. [. . . ]