User manual KYOCERA FS-7000+
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual KYOCERA FS-7000+. We hope that this KYOCERA FS-7000+ user guide will be useful to you.
Manual abstract: user guide KYOCERA FS-7000+
Detailed instructions for use are in the User's Guide.
[. . . ] Table of Contents
Users Manual
Kyocera Laser Printer
FS-7000
The FS-7000+ in this photograph is equipped with two optional paper feeders and an optional document finisher.
Introduction
Caution
NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION.
Notice on Software _____________________________________________________________________________________
SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER'S NATIVE MODE OR ONE OF ITS EMULATION MODES. The emulation mode can be changed by following the procedures described in Chapter 2.
Notice ________________________________________________________________________________________________
The information in this manual is subject to change without notification. The user is asked to excuse any technical inaccuracies or typographical errors in the present edition. No responsibility is assumed if accidents occur while the user is following the instructions in this manual. [. . . ] (See page 5-11. ) Pressing the CONTINUE key will return the printer to Ready status.
Note that the password entered here is reset (returns to 00001) when this mode is exited.
Print VMB Accumulated Data List
This feature prints a list of VMB data accumulated in the RAM DISK.
1. to flash.
>List of VMB ?
Press the CANCEL key if you want to halt printing. Pressing the ENTER key will cause Processing to be displayed and the VMB data list to be
printed.
2-37
Virtual Mail Box (VMB)
An actual VMB list printout will differ slightly from sample given above. Information regarding virtual output trays which are set will be displayed in the virtual mail box list. A - mark is shown with the bin number for virtual output trays which contain data. If a password is set for a virtual output tray, there is no barcode shown for that virtual output tray. Also, "FULL!!" will be shown for virtual output trays for which there was an error when data was sent to them. A VMB ERROR LOG will be printed when data from such a virtual output tray is printed.
2-38
Chapter 2 Operating the Page Printer
Operations for Using a Barcode Reader
If an optional barcode reader (BC-1) is connected to the printer, it is possible to print data within a virtual output tray using the barcode in the list. Select the barcode for "Output (1)" in the upper right using the barcode reader and then select the barcode for the virtual output tray you want to print. If you want to delete the data in a tray, select "Delete (2)" also in the upper right and then select the barcode for the virtual output tray you want to delete. For detailed operating procedures for the barcode reader, please read the instructions included with the barcode reader.
2-39
Memory Card
Memory Card
This printer is equipped with a memory card slot. This allows, for example, the use of fonts other than internal fonts by using an optional font card. 2. 1 memory card is used, it is possible to read, write and delete data and format the memory card.
Note _____________________________________________________________________
Only 32 MB or less flash or S-RAM type memory card conforming to JEIDA Ver. It is possible to set the partitions on the memory card which you wish to execute for the printer at power-on by using the PRESCRIBE 2e FRPO I0 command. For details on the FRPO command, please read the Programming Manual on the supplied CD-ROM. A font card can be read from the control panel or read automatically upon power-on or printer reset when a font card is inserted in the printer.
Inserting Memory Card
Carefully insert the memory card as far as it will go with the top side facing right (back side of the printer).
Memory Card Slot
Memory Card
2-40
Chapter 2 Operating the Page Printer
Notes ____________________________________________________________________
Follow the precautions below when handling a memory card.
· · · · · · · · · · Operating a Memory Card
A memory card is sensitive to static electricity. Before handling a memory card, be sure to eliminate any static electricity which may have built up on your body or clothing by touching a metallic object. Be sure that its power is off when inserting or removing a memory card. Store a memory card in their protective case when not using them.
The following operations on a memory card inserted into the printer's memory card slot are possible.
· · · · · · ·
Reading Fonts Reading Macros Reading Data Writing Data Deleting Data Formatting Memory Card Printing a List of Data Names (Partitions)
2-41
Memory Card
Note that only reading fonts and printing a list of partitions are possible when a font card is inserted. Each operation is described below.
Reading Fonts from a Memory Card
Fonts can be read into the printer's internal memory from an optional font card. The font read can then be selected from the printer's control panel. A font card is automatically read into the printer when the printer's power is turned on. [. . . ] Press the 8 key to move to a submenu.
Press the w key to return.
4. Press the ENTER key.
If you want to re-enter a setting, press the CANCEL key before pressing the ENTER key.
7. This will enable
currently selected settings.
>NetWare Off On >TCP/IP Off On >Ether Talk >TCP/IP Off Off Number of copies 001 >OPT. StatusPage >TCP/IP Off Off
>
>>NetWare Frame Auto
>
>>DHCP OFF >>IP Address
>>Gateway
>>Subnet Mask
Continued on next page
(Continued from previous page)
>Code set ISO-6 ASCII
Emulation HP LJ 5M/5Si
>
(*1)
Emulation KC-GL
>
>KC-GL Pen width >KC-GL Page set
>
>>Pen (1) width 01 dot (s) 01 dot (s)
Emulation KPDL
>
>Print KPDL errs Off On
(*2)
Emulation KPDL (AUTO)
>
>Alt. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE KYOCERA FS-7000+
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual KYOCERA FS-7000+ will begin.