User manual KYOCERA FS-8000C

[. . . ] FS-8000C FS-8000CD FS-8000CN Color Printer Operation Guide Caution NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION. Legal Restriction on Printing It may be prohibited to print copyrighted material without permission of the copyright owner. It is prohibited under any circumstances to print domestic or foreign currencies. Printing other items may be prohibited. Notice on Software SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER'S EMULATION MODE. The emulation mode can be changed by following the procedures described in Chapter 3. Notice The information in this manual is subject to change without notification. [. . . ] When writing data to the storage device, a name is automatically assigned to the data. Otherwise, the >Write Data message explained below will not appear on the display. To format a memory card or the hard disk, see Formatting a Storage Device on page 3-75. You can format the hard disk using the operator panel when the first time you installed a new hard disk. About formatting a new hard disk, see also the Installation Guide of the hard disk for details. Note After writing is complete, you can print a list of data stored in the storage device for confirmation. To write data to a memory card or the hard disk, proceed as follows: 1 2 Press the MENU key. Press the or key repeatedly until Memory Card > or Hard disk > appears. Memory Card > 3 Press the key. 4 Press the or key repeatedly until >Write Data appears. >Write Data 3-72 3. 9 Operating the Storage Device 5 Press the ENTER key. A question mark (?) appears. >Write Data ? 6 7 Press the ENTER key. While the message display indicates Waiting, send the data to write from the computer to the printer. For example, to write data `TEST. TXT' you can use the DOS COPY command as: COPY TEST. TXT PRN The data is written to the memory card or hard disk with a unique partition name which the printer automatically assigns in a sequence as follows: DataS001 (first data), DataS002 (second data), DataS003 (third data), . . . DataS127 (last data) In the example above, data `TEST. TXT' is renamed and stored as `DataS001' in the storage device. 8 As the printer receives data, the message display shows Processing, soon followed by Waiting. The printer automatically prints a Write Information page as shown below: FS-8000C Page Printer WRITE INFORMATION Figure 3-11 3-73 3. 9 Operating the Storage Device This page provides the following information that are automatically generated by the printer while the data is written: · · · · Partition Type Type of data written (only type 2 is supported at the present time) Partition Name Name of data written Write Partition Length Length (size) of the data written Others Additional information, such as error information After the Write Information page is printed, the display returns to Ready. If writing was not successfull, the message display displays an error code. For details, see Chapter 5 Troubleshooting, section 5. 3. 2 Storage Error Codes on page 5-11. The message display returns to Ready. 9 Repeat the above steps until you have written all required data to the storage device. Each time you finish writing data, a Write Information page is printed showing the information about the data just written. Data contained in the storage device can be printed anytime by following the procedure described in Printing a Partition List on page 3-76. Deleting Data You can use the printer's operator panel to delete data from a memory card or the hard disk. 1 2 Press the MENU key. Press the or key repeatedly until Memory Card > or Hard Disk > appears. Memory Card > 3 Press the key. 4 Press the or key repeatedly until > Delete Data appears. The name of the first data in the storage device also appears (DataS001 in this example). >Delete Data DataS001 5 Press the ENTER key. A blinking question mark (?) appears before the data name. >Delete Data ?data name 3-74 3. 9 Operating the Storage Device 6 Press the or key to scroll through data in the storage device. 7 When the data you desire to delete is displayed, press the ENTER key. The message displays shows Processing and the data is deleted from the storage device. Formatting a Storage Device A new memory card or hard disk must be formatted before it can be used in the printer. You can format the storage device using the printer operator panel. · · Note Formatting will destroy any existing data on a storage device. You can format the hard disk using the operator panel when the first time you installed a new hard disk. About formatting a new hard disk, see also the Installation Guide of the hard disk for details. To format a memory card or the hard disk, use the following procedure: 1 2 Press the MENU key. Press the or key repeatedly until Memory Card > or Hard Disk > appears. Memory Card > 3 Press the key. 4 Press the or key repeatedly until >Format appears. >Format 5 Press the ENTER key. A question mark (?) appears. >Format ? 6 Press the ENTER key. The message display shows Processing while the storage device is formatted. [. . . ] The factory settings of the buffer nearly-full and nearly-empty thresholds (H6 and H7) are subject to change without notice. The difference between the nearly-full and nearly-empty thresholds allows the computer to send a fairly large amount of data in a continuous stream. H8: Received data buffer size The input buffer size is specified in increments of 100 kB. The factory setting is 5 (500 kB). B. 3. 2 PRESCRIBE FRPO D0 Command The PRESCRIBE FRPO D0 command is provided to allow manipulating XON/XOFF when an error has occurred on the serial interface. [. . . ]