User manual LENOVO L2362P

[. . . ] L2362p Wide Flat Panel Monitor User's Guide Product numbers L2362pwA 0559-HB1 First Edition (September 2010) © Copyright Lenovo 2010. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C. F. R. 2. 101 with limited and restricted rights to use, reproduction and disclosure. LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or services are delivered pursuant a General Services Administration "GSA" contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. [. . . ] To convert your LCD display from a desk-mounted to a wall-mounted display, do the following: Step 1: Verify that the Power button is turned Off, then disconnect the power cord. Step 2: Lay the LCD display face down on a towel or blanket. Chapter 2. 2-9 Step 3: Revolve the monitor hinge cover and stand, . refer to "Detaching the monitor hinge cover and stand" insure that it is parallel to top of the back side. Step 4: Attatch the mounting bracket from the VESA compatible wall mounting kit (100mm x100mm distance), VESA Mounting Screw M4 x 10 mm. VESA hole Step 5: Attach the LCD display to the wall, following the instructions in the wallmounting kit. For use only with UL Listed Wall Mount Bracket with minimum weight/load: 8kg Chapter 2. 2-10 Chapter 3. Reference information This section contains monitor specifications, instructions to manually install the monitor driver, troubleshooting information, and service information. Monitor specifications Table 3-1. Monitor specifications for type-model L2362pwA Dimensions Height Depth Width Stand Base VESA mount Image Tilt Swivel Supported Viewable image size Maximum height Maximum width Pixel pitch Power input Supply voltage Max supply current 411. 0 mm (16. 18 in. ) 189. 8 mm (7. 47 in. ) 549. 0 mm (21. 61 in. ) Range: -5~ 20 150each side 100 mm x 100 mm (3. 94 in. x 3. 94 in. ) 584. 2 mm (23 in. ) 286. 4 mm (11. 28 in. ) 509. 1 mm (20. 05 in. ) 0. 265 mm (0. 01 in. ) 90-264VAC (100~240VAC+/-10%) 1. 5 A - Power consumption Note: Power consumption figures are for the monitor and the power supply combined. Normal operation Standby/Suspend Off Note: without USB/ Webcam/external speaker Input signal Horizontal addressability <45W <1W(Analog), <1W(Digital) <0. 5W at 100Vac & 240Vac Video input(Analog) Analog Direct Drive, 75 ohm 0. 7V 1920 pixels (max) -- Vertical addressability 1080 lines (max) Clock frequency 205 MHz Chapter 3. 3-1 Table 3-1. Monitor specifications for type-model L2362pwA Video input Input Signal Horizontal addressability HDMI 1920 pixels (max) - Vertical addressability 1080 lines (max) Clock frequency Communications Supported Display Modes VESA DDC Horizontal frequency Vertical frequency Native Resolution Temperature Operating Storage Shipping Humidity Operating Storage Shipping 165 MHz CI 30 kHz - 83 kHz 50 Hz - 75 Hz 1920 x 1080 at 60 Hz 0 to 40 C (32 to 104 F) -20 to 60 C (-4 to 140 F) -20 to 60 C (-4 to 140 F) 10% to 80% non-condensing 5% to 95% non-condensing 5% to 95% non-condensing Chapter 3. 3-2 Troubleshooting If you have a problem setting up or using your monitor, you might be able to solve it yourself. Before calling your dealer or Lenovo, try the suggested actions that are appropriate to your problem. Troubleshooting Problem The words "Out of Range" are shown on the screen, and the power indicator is flashing white. Possible cause The system is set to a display mode which is not supported by the monitor. Suggested action If you are replacing an old monitor, reconnect it and adjust the display mode to within the specified range for your new monitor. If using a Windows system, restart the system in safe mode, then select a supported display mode for your computer. The video signal cable is not connected with the monitor or system completely. Be sure the signal cable is firmly plugged into the system and monitor. "Understanding power management"on page 2-8 "Connecting and turning on your monitor"on page 1-4 "Adjusting your monitor image"on page 2-3 "Adjusting your monitor image"on page 2-3 "Connecting and turning on your monitor"on page 1-4 Reference "Selecting a supported display mode"on page 2-7 · · · · · · Screen is blank and power indicator is orange The monitor is in Standby/Suspend mode · · Chapter 3. 3-3 Table 3-2. Troubleshooting Problem The power indicator is orange, but there is no image. Possible cause The video signal cable is loose or disconnected from the system or monitor. One or more of the pixels appear discolored · Fuzzy lines in text or a blurry image. This is a characteristic of the LCD technology and is not an LCD defect. · Image setup has not been optimized Your system Display Properties setting have not been optimized. Suggested action Be sure the video cable is connected with the system properly. If there are more than five pixels missing, contact the Support Center. [. . . ] The information contained in this document does not affect or change Lenovo product specifications or warranties. Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo or third parties. All information contained in this document was obtained in specific environments and is presented as an illustration. Lenovo may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you. [. . . ]