User manual LENOVO LI2361D

[. . . ] LI2361d Wide Flat Panel Monitor User's Guide Product numbers LI2361dwA 1192-HB1 First Edition (October 2011) © Copyright Lenovo 2011. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C. F. R. 2. 101 with limited and restricted rights to use, reproduction and disclosure. LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or services are delivered pursuant a General Services Administration "GSA" contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. [. . . ] Step 2: Lay the LCD display face down on a towel or blanket. Chapter 2. 2-9 Step 3: Revolve the monitor hinge cover and stand, refer to "Detaching the monitor hinge cover and stand" insure that it is parallel to top of the back side. Step 4: Attatch the mounting bracket from the VESA compatible wall mounting kit (100mm x100mm distance), VESA Mounting Screw M4 x 10 mm. VESA hole Step 5: Attach the LCD display to the wall, following the instructions in the wallmounting kit. For use only with UL Listed Wall Mount Bracket with minimum weight/load: 8kg Chapter 2. 2-10 Chapter 3. Reference information This section contains monitor specifications, instructions to manually install the monitor driver, troubleshooting information, and service information. Monitor specifications Table 3-1. Monitor specifications for type-model LI2361dwA Dimensions Height Depth Width Stand Base VESA mount Image Tilt Swivel Supported Viewable image size Maximum height Maximum width Pixel pitch Power input Supply voltage Max supply current 411. 0 mm (16. 18 in. ) 189. 8 mm (7. 47 in. ) 549. 0 mm (21. 61 in. ) Range: -5~ 20 150each side 100 mm x 100 mm (3. 94 in. x 3. 94 in. ) 584. 2 mm (23 in. ) 286. 4 mm (11. 28 in. ) 509. 1 mm (20. 05 in. ) 0. 265 mm (0. 01 in. ) 90-264VAC (100~240VAC+/-10%) 1. 5 A - Power consumption Note: Power consumption figures are for the monitor and the power supply combined. Video input(Analog) Normal operation Standby/Suspend Off <45W <1W(Analog), <1W(Digital) <0. 5W at 100Vac & 240Vac Input signal Horizontal addressability Analog Direct Drive, 75 ohm 0. 7V 1920 pixels (max) -- Vertical addressability 1080 lines (max) Clock frequency 205 MHz Chapter 3. 3-1 Table 3-1. Monitor specifications for type-model LI2361dwA Video input Input Signal Horizontal addressability HDMI/DVI 1920 pixels (max) - Vertical addressability 1080 lines (max) Clock frequency Communications Supported Display Modes VESA DDC Horizontal frequency Vertical frequency Native Resolution Temperature Operating Storage Shipping Humidity Operating Storage Shipping 165 MHz CI 30 kHz - 83 kHz 50 Hz - 75 Hz 1920 x 1080 at 60 Hz 0 to 40 C (32 to 104 F) -20 to 60 C (-4 to 140 F) -20 to 60 C (-4 to 140 F) 10% to 80% non-condensing 5% to 95% non-condensing 5% to 95% non-condensing Chapter 3. 3-2 Troubleshooting If you have a problem setting up or using your monitor, you might be able to solve it yourself. Before calling your dealer or Lenovo, try the suggested actions that are appropriate to your problem. Troubleshooting Problem The words "Out of Range" are shown on the screen, and the power indicator is flashing white. Possible cause The system is set to a display mode which is not supported by the monitor. Suggested action If you are replacing an old monitor, reconnect it and adjust the display mode to within the specified range for your new monitor. If using a Windows system, restart the system in safe mode, then select a supported display mode for your computer. The video signal cable is not connected with the monitor or system completely. Be sure the signal cable is firmly plugged into the system and monitor. "Understanding power management"on page 2-8 "Connecting and turning on your monitor"on page 1-4 "Adjusting your monitor image"on page 2-3 "Adjusting your monitor image"on page 2-3 "Connecting and turning on your monitor"on page 1-4 Reference "Selecting a supported display mode"on page 2-7 · · · · · · Screen is blank and power indicator is orange The monitor is in Standby/Suspend mode · · Chapter 3. 3-3 Table 3-2. Troubleshooting Problem The power indicator is orange, but there is no image. Possible cause The video signal cable is loose or disconnected from the system or monitor. One or more of the pixels appear discolored · Fuzzy lines in text or a blurry image. This is a characteristic of the LCD technology and is not an LCD defect. · Image setup has not been optimized Your system Display Properties setting have not been optimized. Suggested action Be sure the video cable is connected with the system properly. If there are more than five pixels missing, contact the Support Center. [. . . ] Therefore, the result obtained in other operating environments may vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Users of this document should verify the applicable data for their specific environment. Appendix B. Recycling information Lenovo encourages owners of information technology (IT) equipment to responsibly recycle their equipment when it is no longer needed. [. . . ]