Detailed instructions for use are in the User's Guide.
[. . . ] magicolor 2350 User's Guide
®
1800683-001B
EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500
Thank You
Thank you for purchasing a magicolor 2350 printer. Your magicolor 2350 is specially designed for optimal performance in Windows, Macintosh, UNIX, and other environments.
Trademarks
The following are registered trademarks of MINOLTA-QMS, Inc. : QMS, the MINOLTA-QMS logo, Crown, CrownNet, and magicolor. Other product names mentioned in this guide may also be trademarks or registered trademarks of their respective owners. This product uses Software Developer Kit of Peerless Systems Corporation. [. . . ] Doing so may damage the printer and cause the print quality to deteriorate. If the media stacks too high, your printer may experience media jams and excessive media curl. Make sure two people are available to lift the printer when moving it. When moving the printer, keep the printer level to avoid toner spillage. When lifting the printer, grasp the handles at the top of Tray 1 and at the bottom-right side of the printer (or the handles at the bottom of the duplex unit if it is installed).
Front Even if an optional media tray is installed, be sure to lift the printer as described above. Do not grasp the grip of Tray 2 or the cover on its right side; otherwise, the media tray may be damaged.
WARNING!
If you get toner in your eyes, wash it out immediately with cool water and consult a doctor. Material Safety Data Sheets (MSDS) information can be found at www. minolta-qms. com (click on the Answer Base). If you get toner on your skin, wash it off with cool water and neutral detergent. If you get toner on your clothes, lightly dust them off as much as possible. If some toner remains on your clothes, use cool -- not hot -- water to rinse the toner off, provided your clothing is washable. Make sure any parts removed during cleaning are replaced before you plug in the printer.
Maintaining the Printer
103
EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500
Cleaning the Printer
Always test any cleaning solution (such as a mild detergent) on a small area of your printer to check the solution's performance.
Exterior
This item needs cleaning. . . As needed Use A soft, dry cloth A cotton swab Avoid Sharp or rough implements (such as wire or plastic cleaning pads) Any liquid Printer exterior A soft, damp cloth (mild detergent) Sharp or rough implements (such as wire or plastic cleaning pads) Abrasive or corrosive solutions that contain solvents (such as alcohol or benzene)
Control Panel
Exhaust Duct
Printer Exterior
104
Cleaning the Printer
EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500
Interior
Attention
Be sure to turn off the printer and unplug the power cord before cleaning inside. Use Avoid
Abrasives or A damp cloth that detergents has been wrung out well A soft, dry Liquids, cloth abrasives, or detergents
Tray 1 interior feed Every 30, 000 single-sided rollers pages, every 12 months, or as needed, whichever comes first. Every 30, 000 single-sided pages, every 12 months, or as needed, whichever comes first. Every 30, 000 single-sided pages, every 12 months, or as needed, whichever comes first.
Printer interior (such as the inside of the door, around the waste toner bottle)
Media Rollers
The accumulation of paper dust and other debris on the paper transport roller can cause media-feeding problems.
Tray 1 (Multipurpose Tray) Interior Feed Rollers
1
Remove all media from Tray 1.
Cleaning the Printer
105
EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500
2
Pull the right-side door release , and then open the right-side door .
3
While pressing down the media guide with one hand, clean the feed roller by wiping it with a soft, dry cloth. While the door is open, the paper feed roller inside the right door can also be cleaned. While pressing the paper guide down with one hand, clean the paper feed roller by wiping it with a soft, dry cloth.
Media guide
4 5 6
Close the media guide. Media feed roller
Duplex Option Feed Rollers
1 2
Turn off and unplug the printer and disconnect the interface cable. Open the cover of the duplex option.
106
Cleaning the Printer
EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500
3 4 5
Clean the feed rollers by wiping them with a soft, damp cloth that has been wrung out well. In compliance with UL guidelines, "The appliance inlet is considered to be the main disconnect device. "
Tray 2 (Optional Lower Feeder Unit) Media Rollers
1 2 3
Turn off and unplug the printer and disconnect the interface cable. Remove the brackets (two at the front and one at the back) used to attach the lower feeder unit to the printer. Opening the front door and removing the waste toner bottle first will permit a clearer view of these brackets.
WARNING!
Your printer weighs approximately 62 lbs (28 kg) with consumables installed. [. . . ] Make sure that the power cord is: Switched off immediately and unplugged if the power supply cord is damaged. Correctly plugged into the socket and that the socket is visible at all times and is readily accessible. Not underneath the printer or another machine as this can result in damage to that cord. The result could be a fire or improper functioning of the unit in question. [. . . ]