Detailed instructions for use are in the User's Guide.
[. . . ] In the standard setting, Auto Low Power operates automatically when 15 minutes have elapsed after completion of the last copy, with the copier remaining in the ready to copy state during that time. The time period for the Auto Low Power function can be set for 5 minutes, 10 minutes, 15 minutes, 30 minutes, 60 minutes, 90 minutes, 120 minutes, or 240 minutes. 2-20 for details.
Automatic Shut-Off
This function achieves further energy conservation by partially turning OFF the power supply, thereby reducing energy consumption to 20W or less. In the standard setting, Automatic Shut-Off follows Auto Low Power, operating automatically when 90 minutes have elapsed after completion of the last copy, with the copier remaining in the ready to copy state during that time. [. . . ] Trays for copy paper, front/back covers, and insertions should have the same paper size loaded. insert sheets: 30 locations, from 1~999, including front and back covers The LCT cannot be selected as tray source if specified as Thick 3. Incompatible Conditions: APS, Group, Rotation Sort, Rotaion Group, Fold/ Stitch&Fold/ Trimming (with Booklet selected), Mixed Original, Tab Paper, Combination, Booklet, OHP Interleave, Image Insert, Dual Page, Program Job, Non-image Area Erase, Repeat (except 2/4/8 Repeat), AUTO Layout, Overlay, Storing Image in Overlay Memory
FRONT COVER COPIED
SURVEYOR'S 1 REPORT
10 89 67 45 23 4 23 56 9 10 78
Application Selection Screen Sheet/Cover Insertion Chapter
FRONT COVER BLANK
SURVEYOR'S 1 REPORT
10 89 67 45 23 2 SURVEYOR'S 1 REPORT 34 56 9 10 78
Combination
Booklet OHP Interleave
SURVEYOR'S 1 REPORT
Originals
Copies
Originals
Copies
Image Insert
BACK COVER COPIED
SURVEYOR'S REPORT
9 10 78 56 34 12 2 SURVEYOR'S 1 REPORT 34 9 7 8 10 56
BACK COVER BLANK
SURVEYOR'S 1 REPORT
10 89 67 45 23 2 SURVEYOR'S 1 REPORT 34 56 9 10 78
Dual Page
Program Job Non-Image Area Erase Reverse Image Repeat
Originals
9 10 78 56 34 12
Copies
Originals
9 10 78 56 34 12
Copies
9 10
COPY SHEET INSERTION
SURVEYOR'S REPORT
2 4 SURVEYOR'S 1 REPORT 3 56 10 89 7
BLANK SHEET INSERTION
SURVEYOR'S REPORT
2 SURVEYOR'S 1 REPORT 3 4 56 78
Originals
Copies
Originals
Copies
Applications Combination samples: FRONT & BACK COVERS COPIED, AND COPY SHEET INSERTION
SURVEYOR'S 1 REPORT
10 89 67 45 23 23 56 7 4 89 10
9
AUTO Layout
FRONT & BACK COVERS BLANK, AND BLANK SHEET INSERTION
SURVEYOR'S REPORT
9 10 78 56 34 12 3 12 6 45 78 9 10
Frame/Fold Erasure
SURVEYOR'S 1 REPORT
SURVEYOR'S REPORT
Full-Image Area Image Shift Reduce & Shift Stamp
Overlay Overlay Memory
9-3
Inserting Sheets and Covers (Sheet/Cover Insertion) (continued)
1.
Load regular sheets into any tray, and insertion sheets and covers into each tray source to be designated on the Sheet/Cover Insertion Screen.
DETAILS
· When using thick paper or tabbed paper for covers or insertions, load them in the Multi-sheet bypass tray, unless previously specified and loaded in any other tray. · Be sure that the trays for copy paper, front/back covers, and insertions have the same paper size loaded.
2.
Touch APPLICATION on the Basic Screen.
Reminder!
When starting a new copying job, be sure to close the RADF securely, then press [AUTO RESET].
3.
Touch Sheet/Cover Insertion on the Application Selection Screen.
The Sheet/Cover Insertion Screen will be displayed.
4.
Select the desired cover mode.
Example: Touch FRONT COPY to insert a copied front cover.
5.
Touch CHANGE COVERS TRAY to select the cover sheet tray source.
The tray source for covers currently selected is displayed on the Sheet/Cover Insertion Screen. Every touch of the key shifts the selection in the display that includes paper type as specified in Key Operator mode. If no insertion is desired, proceed to step 8.
9-4
Inserting Sheets and Covers (Sheet/Cover Insertion) (continued)
6.
When selecting Insertion mode: Enter the page number.
Application Selection Screen Sheet/Cover Insertion Chapter
Touch to select the desired insertion mode, then use the control panel keypad to enter the page number of insertion location. The insertion location will be deleted.
Combination
Booklet OHP Interleave Image Insert
HINT
See p. 9-6 for details on entering page numbers.
7.
Touch CHANGE INSERTION TRAY to select the insertion tray source.
The tray source for covers currently selected is displayed on the Sheet/Cover Insertion Screen. Every touch of the key shifts the selection in the display that includes paper type as specified in Key Operator mode.
Dual Page
Program Job Non-Image Area Erase Reverse Image Repeat
8. 9.
When all settings are completed, touch OK to return to the Basic Screen. Enter the desired print quantity from the control panel keypad.
HINT
See p. (Normally the fixed size of Tray 1 will be selected. ) The LCT cannot be selected as tray source if specified as Thick 3. Incompatible Conditions: APS, Group, Rotation Sort, Rotation Group, Fold/ Stitch&Fold/ Trimming (with Booklet selected), Mixed Original, Sheet/Cover Insertion, Chapter, Booklet, OHP Interleave, Image Insert, Dual Page, Program Job, Non-Image Area Erase, Repeat, Storing Image in Overlay Memory
4 in 1 copying 2 in 1 copying
Original
1 1 2 3
2
8 in 1 copying
1234 4 5678
1.
Touch APPLICATION on the Basic Screen.
Reminder!
When starting a new copying job, be sure to close the RADF securely, then press [AUTO RESET].
2.
Touch Combination on the Application Selection Screen.
The Combination Mode Selection Screen will be displayed.
9-10
Lay Out Several Pages onto One Sheet (Combination) (continued)
3.
Select the desired Combination mode.
Application Selection Screen Sheet/Cover Insertion Chapter
Touch 2 in 1, 4 in 1 or 8 in 1 in the desired order area, referring to the illustration on the following page.
Combination
4. 5.
Touch OK.
The Application Selection Screen will be restored.
Booklet OHP Interleave Image Insert
Touch OK on the Application Selection Screen.
The Basic Screen will be restored.
Dual Page
Program Job Non-Image Area Erase Reverse Image Repeat
AMS is automatically selected. When selecting any tray other than the one that is set and displayed on the Basic Screen, touch the desired tray key.
Applications
Frame/Fold Erasure AUTO Layout Full-Image Area Image Shift Reduce & Shift Stamp
6.
9
Select the desired original direction.
Touch SPECIAL ORIGINAL on the Basic Screen to display the Special Original popup menu. Touch to select the desired original direction, then touch OK to return to the Basic Screen.
Overlay Overlay Memory
7.
Enter the desired print quantity from the control panel keypad.
HINT
See p. 3-7 for details on setting print quantity.
9-11
Lay Out Several Pages onto One Sheet (Combination) (continued)
8.
Position originals FACE UP in the document feeder.
HINTS
· For details on positioning originals, see p. CAUTION
When the finisher / paper exit tray capacity is exceeded due to the print quantity selected, remove the copied sets as they exit; otherwise, mishandled paper will occur.
DETAILS: Original Type and Layout Order
Refer to the table below to select the desired Combination mode.
Layout Original Portrait type 1 1 2 3 4 2 1234 5678 2 4 1 3 1357 2468 2 in 1 Horizontal order 4 in 1 8 in 1 Vertical order 4 in 1 8 in 1
Landscape type 1 2 1 3 2 4
1 3 5 7
2 4 6 8 1 2 3 4
1 2 3 4
5 6 7 8
9-12
Making a Multiple Page Signature Booklet (Booklet)
Use the Booklet function to make a multiple page signature booklet copied on both sides of the paper from any tray unless it is specified as Thick or Tab paper of the paper type in the Key Operator mode. Original images are scanned into memory and automatically arranged in booklet format in the correct order. Original pages should be a multiple of 4 in 1-2 mode or a multiple of 2 in 2-2 mode; otherwise blank pages are automatically inserted to the last. Incompatible Conditions: APS, 1 1, 2 1, Group, Rotation Sort, Rotation Group, Face Up, Cover sheet feeder with Cover mode in Booklet, Mixed Original, Tab Paper, Sheet/Cover Insertion, Combination, OHP Interleave, Program Job, NonImage Area Erase, Repeat, Storing Image in Overlay Memory
Application Selection Screen Sheet/Cover Insertion Chapter
Combination
Booklet OHP Interleave
47 48
1-sided originals
1 2 3 4
. . . . . . . . . . . . . .
Image Insert
Booklet copying
47 45 2 48 1
3
. . . . . . . . . . . . . .
Dual Page
24 25 26 23
4 46 3
7
. . . . . . . . . . . . . .
Program Job Non-Image Area Erase
48
1
5
45
47
2-sided originals
2 4 6 8
46
Reverse Image Repeat
1.
Load Copy Paper.
Load the desired copy paper size in a tray. When selecting cover sheet mode (Cover with Copy sheet or Cover with Blank sheet), load the same size paper in any other tray unless it is specified as Thick or Tab paper of the paper type in the Key Operator mode.
Applications
Frame/Fold Erasure AUTO Layout
9
2.
Touch APPLICATION on the Basic Screen.
Reminder!
When starting a new copying job, be sure to close the RADF securely, then press [AUTO RESET].
Full-Image Area Image Shift
3.
Touch Booklet on the Application Selection Screen.
Reduce & Shift Stamp
Overlay Overlay Memory
9-13
Making a Multiple Page Signature Booklet (Booklet) (continued)
4.
Touch to highlight the desired Booklet mode key.
When a cover sheet is required, touch CHANGE COVERS TRAY to select the cover sheet tray source. [. . . ] The selected key will be deleted from the screen.
13-52
[19] Scan Transmission Setting (continued)
To change the address: (1) Touch to highlight the desired name key, then touch CHANGE. The subsequent screen according to the address type will be displayed. (See previous page. ) (2) Touch to highlight the registered item key on the left, then change the information under that key using the alphabet keys on the screen. (3) Touch OK on each screen to complete the setting and restore the Scan Transmission Setting Screen. [. . . ]