User manual ONE FOR ALL SV-9510

[. . . ] 3-6 Copier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6 Inside the Copier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9 Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] You can make copies automatically from originals of assorted sizes loaded in the Automatic Document Feeder. Refer to "Mixed Originals. " (p. 4-4) 3 Make the necessary settings. Making Copies (p. 5-1) Advanced Copying (p. 6-1) 4 Press the [START] key to start feeding and copying the originals from the top page. 4-3 Konica7115_7118. book Page 4 Tuesday, October 16, 2001 10:51 AM 4 Mixed Originals Loading Originals A stack of originals of different sizes can be copied as a set using the Automatic Document Feeder. Originals Copies (APS) Note This feature can be used only if the width of the originals is the same. E. g. : A3L and A4C Making Copies from Originals of Mixed Sizes 1 Slide the front adjustable Document Guide Plate to the front of the copier. 2 Load the originals face up in the Document Feeder Tray so that their rear edges are in correct alignment with the Document Guide Plate. 4-4 Konica7115_7118. book Page 5 Tuesday, October 16, 2001 10:51 AM Loading Originals 4 3 Press the front adjustable Document Guide Plate tightly up against the front edges of the originals. ?Is the stack of originals neat? The maximum number of originals that can be loaded is 50. Be sure that the top level of the original stack does not exceed the Ä marking. Be sure that the Document Guide Plates touch both the front and rear edges of the original stack. If they are not pressed snugly against the original stack, skewed feeding could result. 4 Press the [ORIGINAL] key to light the MIXED ORIGINAL lamp. 5 Press the [APS/AMS] key to light the APS lamp. 6 Press the [START] key to start feeding and copying the originals from the top page. 4-5 Konica7115_7118. book Page 6 Tuesday, October 16, 2001 10:51 AM 4 4. 3 Loading Originals Place the Original on the Original Glass The method for positioning the original differs depending on the type of original being used. Be sure to use the appropriate method that best suits the type of original. Refer to p. 4-2 for information on using the Automatic Document Feeder. Precautions for Placing the Original on the Original Glass Care should be used when positioning the following types of originals. An original of a nonstandard size: G The copier is unable to detect the original size automatically, meaning that neither APS nor AMS can be used. 5-3 Konica7115_7118. book Page 4 Tuesday, October 16, 2001 10:51 AM 5 Manual Paper Selection Making Copies 1 Position the original. Original Loading. (p. 4-1) 2 Press the [PAPER SIZE] key on the control panel until the desired paper size indicator lights. 3 Make the other necessary settings. Zoom Ratio (p. 5-11) Image Density (p. 5-16) 4 Enter the number of copies to be made from the Key Pad and press the [START] key. Tip The Display shows different marks according to the type of paper set by selecting User's Choice. Details: OHP transparencies Cards and postcards Plain paper If plain paper is set in User's Choice, the "1" mark will not be displayed even if cards or postcards, or OHP transparencies, are loaded in the tray. 5-4 Konica7115_7118. book Page 5 Tuesday, October 16, 2001 10:51 AM Making Copies 5 5. 3 Feeding Paper Manually Paper can be fed manually through the Bypass Tray if you want to copy onto paper that is not loaded in any tray, or if you want to copy onto special paper, such as OHP transparencies, postcards, or cards. Types of paper that can be fed through the Bypass Tray G G G Plain paper (weighing 60 g/m2 to 90 g/m2) Recycled paper (weighing 60 g/m2 to 90 g/m2) Special paper: Card (weighing 91 g/m2 to 157 g/m2), OHP transparencies, postcards, and labels Maximum size: 297 mm x 432 mm Minimum size: 90 mm x 140 mm Sizes of paper that can be fed through the Bypass Tray G G Note Insert one sheet of paper at a time when using the Manual Bypass Tray to make a copy. If the optional Multiple Bypass is mounted, the Bypass Tray can hold up to 50 sheets of paper, or 20 sheets of cards, postcards, or OHP transparencies. 5-5 Konica7115_7118. book Page 6 Tuesday, October 16, 2001 10:51 AM 5 Making Copies by Using the Bypass Tray <Manual Bypass Tray> Making Copies 1 Position the original. Original Loading (p. 4-1) 2 Slide the Paper Guides to the size of the paper. Note that the Bypass Tray location indicator on the control panel lights. Do youother than plaintype of paper paper? To use cards, postcards, or OHP transparencies, first change the type of paper selecting User's Choice. When loading cards or postcard, be sure to smooth out any curl in the paper. 3 Press the [BYPASS TRAY] key until the size of the paper loaded lights. ? If the paper used is of custom size, its size must be input. Refer to the "Custom Size Input (Bypass Tray)" procedure that follows. if you want to change the FLS size. 4 Press the [ENTER] key. 5-6 Konica7115_7118. book Page 7 Tuesday, October 16, 2001 10:51 AM Making Copies 5 Zoom Ratio (p. 5-11) Image Density (p. 5-16) 5 Make any other necessary settings. 6 Press the [START] key. Tip If the same settings apply to the second and subsequent sheets of paper, you have only to load the paper in the Bypass Tray: This will automatically start the new copy cycle. Tip To make copies continuously on cards, OHP transparencies, or postcards, load the paper in the 1st Tray. Refer to "Copy Paper"(p. 322) and "Adding Paper" (p. 8-4). 5-7 Konica7115_7118. book Page 8 Tuesday, October 16, 2001 10:51 AM 5 <Multiple Bypass Tray> Making Copies 1 Position the original. Original Loading (p. 4-1) 2 Adjust the Paper Guides and the Bypass Tray Extender to the size of the paper. [. . . ] 50 sheets (80 g/m2) 36 W or less Width: 602. 5 mm Depth: 502 mm Height: 110 mm 6. 2 kg Capacity of Document Feeder Tray Power Consumption Dimensions Weight Paper Feed Cabinet PF-121 Specifications Kinds of Paper Paper Size Plain paper (60g/m2 to 90 g/m2), recycled paper A3L to A5C, FLS (210 mm × 330 mm) Inch system equivalent 11 × 17L, 11 × 14L, Legal L, Letter, 5-1/2 × 8-1/2C 250 sheets 9 W or less Width: 535 mm Depth: 568 mm Height: 137 mm 5. 5 kg Capacity Power Consumption Dimensions Weight 10-3 Konica7115_7118. book Page 4 Tuesday, October 16, 2001 10:51 AM 10 Shifting Unit IS-101 Specifications Shift Position Capacity Power Consumption 28mm 250 sheets 63 W or less Appendix Job Tray IT-102 Specifications Kinds of Paper Plain paper (60g/m2 to 90 g/m2), recycled paper Special paper: card (91 g/m2 to 157 g/m2), OHP transparencies, postcards, labels <Upper Copy Tray> · Plain paper (80g/m2), recycled paper: A4 100 sheets, sizes other than A4 50 sheets (max. height 22 mm) · Special paper: 10 sheets <Lower Copy Tray> · Plain paper (80g/m2), recycled paper: A4 150 sheets, sizes other than A4 75 sheets · Special paper: 20 sheets 63 W or less Capacity Power Consumption Multiple Bypass Tray MT-102 Specifications Kinds of Paper Plain paper: (60g/m2 to 90 g/m2), recycled paper Special paper: card (91 g/m2 to 157 g/m2), OHP transparencies, postcards, labels Width: 90 mm to 297 mm Length: 140 mm to 432 mm Plain paper, recycled paper: 50 sheets Special paper: 20 sheets 9 W or less Width Max. : 436 mm Depth: 489 mm Height: 137 mm Approx. 2. 7 kg Paper Size Capacity Power Consumption Dimensions Weight 10-4 Chapter10. fm Page 5 Tuesday, October 16, 2001 1:16 PM Appendix 10 10. 2 Care of the Copier Cleaning Turn OFF the copier before cleaning it. Housing Cover Wipe the surface of the housing cover with a soft cloth dampened with a mild household detergent. Original Pad Wipe the surface of the Original Pad clean with a soft cloth dampened with alcohol. Platen Glass Wipe the surface of the Platen Glass clean with a soft, dry cloth. Control Panel Wipe the surface of the control panel clean with a soft, dry cloth. [. . . ]