User manual PENTAX R-322EX

[. . . ] TOTAL STATION R-300X INSTRUCTION MANUAL FOR R-300X SERIES BASIC R-315EX R-325EX R-335EX R-322EX R-323EX R-326EX R-315NX R-325NX R-335NX R-322NX R-323NX SERIES PENTAX Industrial Instruments Co. , Ltd. 2-36-9, Maeno-cho Itabashi-ku, Tokyo 174-0063 Japan Tel. +81 3 3960 0502 Fax +81 3 3960 0509 E-mail: international@piic. pentax. co. jp Website: www. pentax. co. jp/piic/survey www. pentaxsurveying. com Before using this product, be sure that you have thoroughly read and understood this instruction manual to ensure proper operation. After reading this manual, be sure to keep in a convenient place for easy reference. Copyright © 2005 PENTAX Industrial Instruments Co. , Ltd. The PTL software and publication or parts thereof, may not be reproduced in any form, by any method, for any purpose. [. . . ] This mode can be performed by selecting the "LONG" at 1. REF. LESS RANGE. · The WARNING (Laser Power) screen is displayed when Range LONG and Message ON are selected, and then F1-MEAS key is pressed. · Pressing [MEAS] one time selects "Second MEAS setting" and twice selects "QUIT" . And then, Normal or Long measurement is selected by pressing F3 or F5. 39 1 2 3 4 There is a possibility that correct distance measurement may be impossible by dispersion or reduction of laser beam when the laser beam comes into the target from diagonal angle. There is a possibility that the instrument cannot calculate correctly when receiving reflected laser beam from forth and back directions in case of measuring the target on the road. There is a possibility that synthesized values are calculated and the distance may become longer or shorter than the actual one when the operator measures the target of slope or sphere or rugged shape. There is a possibility that the instrument cannot calculate correctly collecting the reflected laser beam from a man or a car that comes and goes in front of the target. [Distance measurement by reflector sheet mode] Position the Reflector sheet whose reflecting surface faces the aiming line to be approx. right angle, there is a possibility that correct distance measurement may be impossible by dispersion or reduction of laser beam. [Applied measurement range by each target mode] · When a wrong target mode is selected, a correct distance cannot be measured. · Reflector sheet mode and prism mode: It is sometimes possible to measure without reflector sheet or prism under special conditions like in the close distance, targeting on a wall surface. However, there is a possibility including some errors in this case, so be sure to select the reflectorless mode. · The target constant should be correctly selected and confirmed in case that the reflector sheet is used at the prism mode and the prism is used at the reflector sheet mode. 40 6. 2 Distance measurement The R-300X series has two distance measurement modes of primary MEAS and second MEAS. Pressing the [F1] [MEAS] one time goes to MEAS and twice goes to second MEAS. You can freely select and allocate your desired measurement mode in primary MEAS and second MEAS by the Initial Setting 2. The "MEASURE SHOT" is set at primary MEAS and "TRACK CONT" is set at second MEAS as a Factory default setting. · MEASURE SHOT means the distance measurement by the shot mode. · MEASURE CONT means the distance measurement by the continuous mode. · TRACK SHOT means the fast distance measurement by the shot mode. · TRACK CONT means the fast distance measurement by the continuous mode. Confirm the target constant before beginning the distance measurement. Example:"MEASURE SHOT" at primary MEAS (Factory default setting) Collimate the telescope at a target and press MODE A 15°C S0 the [F1] [MEAS] once to start measuring the distance. H. angle Once distance measurement has been started, 92° 30' 20" H. dst. [. . . ] It is extremely difficult to judge when weather conditions are "Good" and when they are "Normal" With this instrument, the conditions noted below are used to differentiate . between the two situations, (good weather conditions for surveying are different from normal weather conditions, and in surveying situations, cloudy skies are considered more favorable than sunny skies. ) Weather conditions for measurement ranges are based on the following standard values: Normal: Visibility of approximately 20 km, with slight shimmer and moderate wind. Good: Visibility of approximately 40 km, overcast, with no shimmer and moderate wind. 74 14. NOTICE TO THE USER OF THIS PRODUCT To assure compliance with the Safety standard 21 CFR, Chapter 1. [. . . ]