User manual SMEG CS20NLK

[. . . ] Contents 1 Instructions 1. 1 1. 2 1. 3 1. 4 1. 5 1. 6 1. 7 2. 1 2. 2 2. 3 2. 4 2. 5 General safety instructions Identification plate Manufacturer liability Appliance purpose This user manual Disposal How to read the user manual General Description Cooking hob Control panel Other parts Available accessories Instructions First use Using the accessories Using the hob Using the storage compartment Using the oven Cooking advice Programmer clock Instructions Cleaning the appliance Removing the doors Cleaning the door glazing Cleaning the inside of the ovens Pyrolytic: automatic cleaning of the main oven (on some models only) Extraordinary maintenance Gas connection Adaptation to different types of gas Electrical connection Positioning 48 48 49 49 49 49 50 50 2 Description 51 51 52 52 54 54 3 Use 3. 1 3. 2 3. 3 3. 4 3. 5 3. 6 3. 7 3. 8 4. 1 4. 2 4. 3 4. 4 4. 5 4. 6 4. 7 5. 1 5. 2 5. 3 5. 4 57 57 58 58 60 61 61 65 66 4 Cleaning and maintenance 72 72 72 73 74 74 76 77 5 Installation 79 79 82 86 87 We advise you to read this manual carefully, which contains all the instructions for maintaining the appliance’s aesthetic and functional qualities. For further information on the product: www. smeg. com 47 EN Instructions 1 Instructions 1. 1 General safety instructions Risk of personal injury • During use the appliance and its accessible parts become very hot. • Keep children under eight years of age at a safe distance if they are not constantly supervised. • This appliance may be used by children aged at least 8 and by people of reduced physical and mental capacity, or lacking in experience in the use of electrical appliances, provided that they are supervised or instructed by adults who are responsible for their safety. [. . . ] • Keep the inside of the appliance clean at all times. 3. 8 Programmer clock 1 Minute minder timer key 2 End of cooking key 3 Time setting and reset key 4 Value decrease key 5 Value increase key The programmer clock only controls the left main oven and does not control the auxiliary oven. Setting the time On the first use, or after a power failure, the display flashes at regular intervals. Press again for two seconds to start the procedure for setting the current time. Use the keys or to increase or decrease the time value by one minute each time you press the key until setting the required time. The clock starts working 5 seconds after the last key was pressed. 66 Use Timed cooking Timed cooking is the function which allows a cooking operation to be started and then ended after a specific length of time set by the user. The pointer moves to position 12 and the symbol will flash on the display. Once the required time is obtained, cooking will start about 5 seconds after you last pressed the key or . The display will show the current time, represented by the constantly illuminated segments, and the minutes left to the end of cooking, represented by the flashing segments (each flashing segment means 12 minutes of cooking time left). At the end of cooking, the timer will switch the oven heating elements off, the buzzer will start to sound and the numbers on the dial will flash. The set program can be cancelled: Press the key for 2 seconds to cancel the set time and switch the oven off manually if a cooking operation is in progress. To set the cooking time press the key or within 5 seconds: each time you press the key adds 1 minute to the cooking time, and every 12 minutes a new internal segment will light up (the example below shows a cooking time of 1 hour). 67 EN Use Programmed cooking Programmed cooking is the function which allows a cooking operation to be started at a set time and then ended after a specific length of time set by the user. Set the cooking time as described in the previous point “Timed cooking”. Within 5 seconds after the last time you pressed the key or , press the key again to set the cooking end time. The symbol will flash on the display together with the current time, with the internal segments illuminated to show the end of cooking time. Five seconds after the last time you pressed a key, the display will show the current time and the cooking start and end times, represented by the illuminated internal segments. As soon as the current time reaches the set cooking start time, the internal segments will flash and the oven starts cooking. At the end of cooking, the timer switches the oven heating elements off, the buzzer starts to sound and the numbers on the dial flash. The set program can be cancelled: Press the key for 2 seconds to cancel the set time and switch the oven off manually if a cooking operation is in progress. • In the example below, the current time is 7. 06 and cooking is programmed to start at 8. 00 and end at 9. 00. • At 8 o'clock the internal segments between 8 and 9 will start to flash. For the oven to start cooking after the programming procedures just described, the knobs must be correctly set on the required temperature and function. 68 Use Display reduced brightness To reduce energy consumption in stand-by, briefly press the key to reduce the display brightness. Timer This function only activates the buzzer, without stopping cooking. Press the key and the display will light up as shown in the figure below. [. . . ] Perform the ground connection using a wire that is 20 mm longer than the other wires. 5 x 1. 5 mm² five-core cable. Multifunction model The appliance can work in the following modes: Pyrolytic model 3 x 2. 5 mm² three-core cable. • 380-415 V 3N~ • 220-240 V 1N~ 3 x 2. 5 mm² three-core cable. 85 EN • 220-240 V 1N~ Installation 5. 4 Positioning The values indicated above refer to the cross-section of the internal conductor. The aforementioned power cables are sized taking into account the coincidence factor (in compliance with standard EN 60335-2-6). [. . . ]