User manual SMEG P755ASB-1

[. . . ] 9 USING THE HOB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 CLEANING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 POSITIONING IN THE COUNTER TOP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 ELECTRICAL CONNECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The illicit disposal of the product by the user results in the application of administrative sanctions. The product does not contain substances in quantities sufficient to be considered hazardous to health and the environment, in accordance with current European directives. 3. 2 Your environmental responsibility Our product's packaging is made of non-polluting materials, therefore compatible with the environment and recyclable. You can obtain the addresses of collection, recycling and disposal centres from your retailer or from the competent local organisations. Do not discard the packaging or any part of it, or leave it unattended. It can constitute a suffocation hazard for children, especially the plastic bags. Important: hand over your appliance to the local agency authorised for the collection of household appliances no longer in use. Before disposing of your appliance it is important to remove doors and leave shelves in the same position as for use, to ensure that children cannot accidentally become trapped inside during play. It is also necessary to cut the connecting cable to the power supply, removing it along with the plug. 8 Instructions for the user 4. DESCRIPTION OF CONTROLS 4. 1 Control zone All the hob controls are grouped together at the centre front. CONTROL ZONE KNOB DESCRIPTION To light the flame, press the knob and, at the same time, turn it anticlockwise to the maximum flame symbol . To adjust the flame, turn the knob to the zone between the maximum and minimum settings. Rinse thoroughly and dry with a soft cloth or chamois leather. 14 Instructions for the user 6. 2 Cleaning the components 6. 2. 1 Knobs The knobs should be cleaned with a soft cloth dampened with lukewarm water, then dried carefully. Do not use aggressive products containing alcohol or products for cleaning steel and glass when cleaning the knobs, as these products could cause permanent damage. 6. 2. 2 Racks Remove the racks and clean them with lukewarm water and nonabrasive detergent, making sure to remove any encrustations. Wash them with lukewarm water and non-abrasive detergent, making sure to remove any encrustations. To remove burned on food residue, use Puliforno with a scourer sponge. For less stubborn residue and for polishing, use stainless steel cream cleaner Crema Inox with a microfiber cloth. After cleaning ensure they are perfectly dry and reposition them correctly. 6. 2. 4 Igniters and thermocouples For correct operation the igniters and thermocouples must always be perfectly clean. Remove any dry residues with a wooden toothpick or a needle. 15 Instructions for the installer 7. POSITIONING IN THE COUNTER TOP The following operation requires building and/or carpentry work so must be carried out by a competent tradesman. Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminated wood as long as they are heat resistant (T 90°C). 7. 1 Fixing to the supporting structure Create an opening with the dimensions shown in the figure in the top surface of the counter, keeping a minimum distance of 50 mm from the rear edge. [. . . ] Connection with a rigid copper hose: The connection to the gas supply network must be made in such a way that it does not cause stresses of any type on the appliance. The connection can be made using the adapter unit D with double cone, always inserting gasket C (provided) in between. Connection with a flexible steel hose: use only continuous wall stainless steel hoses that comply with the applicable standards, making sure to always insert gasket C (provided) between connector A and flexible hose E. Installation with flexible hose must be carried out so that the length of the piping does not exceed 2 metres when fully extended; make sure that the hoses do not come into contact with moving parts and that they are not crushed in any way. 19 Instructions for the installer 9. 1 Connection to liquid gas Use a pressure regulator and make the connection on the gas cylinder following the guidelines set out in the regulations in force. [. . . ]