User manual SMEG S2641TCU

[. . . ] This symbol alerts you to potential hazards that can kill or hurt you and others. UNDERSTAND SIGNAL WORDS A signal word – DANGER, WARNING, or CAUTION – is used with the safety-alert symbol. It means you can be killed or seriously injured if you do not immediately follow the instructions. [. . . ] COOKTOP MEASUREMENTS NOTE: Observe all governing codes and ordinances. Some cabinet and building materials are not designed to withstand the heat produced by the cooktop. Check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. When installing a range under existing cabinets and the installation does not satisfy the minimum cabinet clearances, install a range hood above the cooktop to avoid burn hazards. 6 Instructions for the Installer 3. POSITIONING THE COOKTOP AND LOCATION REQUIREMENTS NOTE: The following operation requires building and/or carpentry work and must therefore be carried out by a competent technician. Installation can be carried out on various material, such as masonry, metal, solid wood, plastic laminated wood etc. It is the responsibility of the installer to comply with installations guidelines specified on the model/ serial I. D. Electrical connection” section. - - The measurements in the tables referring to the figure below must be followed when attaching the appliance to the support structure. 7 Instructions for the Installer MODEL WITH FRAME Cooktop width 30” 758 mm 36 ” 900 mm MINIMUM DISTANCE A 29 1/8” 750 mm 35 1/8” 892 mm B 19 11/16” 500 mm 19 11/16” 500 mm C 5 11/16” 145 mm 5 11/16” 145 mm D 2” 50 mm 2” 50 mm E 2” 50 mm 2” 50 mm F 2 1/16” 52 mm 2 1/16” 52 mm G 30” 758 mm 36 ” 900 mm MODEL WITHOUT FRAME Cooktop width 24” 610 mm 30 “ 762 mm 36 “ 914 mm MINIMUM DISTANCE A 22 1/4” 565 mm 28 3/8” 721 mm 34 ” 864 mm B 19 2/16” 485 mm 19 1/16” 485 mm 19 1/16” 485 mm C 5 11/16” 145 mm 5 11/16” 145 mm 5 11/16” 145 mm D 2” 50 mm 2” 50 mm 2” 50 mm E 2” 50 mm 2” 50 mm 2” 50 mm 13/ F 1 7/8” 48 mm 1 7/8” 48 mm 16” G 24” 610 mm 30 “ 762 mm 36 “ 914 mm - 1 9/16” 48 mm 3. 1 Mounting Before mounting the device to the unit, lay the provided adhesive sponge onto the glass surface to separate it from the unit. After fixing the provided adhesive sponge (B) to the glass, mount the device to the unit using the mounting brackets (A) provided, as shown in the figure. When fixing the cooktop to the cabinet, use only the holes provided, as illustrated here. NOTE: This appliance must not be built-in above a dishwasher. Installation of an oven without a cooling fan underneath the cooktop is forbidden. 8 Instructions for the Installer Pass the power supply cable through the back of the unit, making sure that it does not touch the bottom casing of the cooktop or the oven (if any) installed below it. 3. 1. 1 Over empty kitchen unit or drawers Failure to install the double-layer wooden base exposes the user to possible accidental contact with sharp or hot parts. The manufacturer declines all responsibility for damage to persons or things caused by failure to comply with the above guidelines. If there are other pieces of furniture (lateral walls, drawers, etc. ), dishwashers or refrigerators, under the hob, a double-layer wooden base must be installed at least 30 mm from the bottom of the hob to avoid any accidental contact. It must only be possible to remove the double-layer base using suitable equipment. opens on bottom opens on rear 9 Instructions for the Installer 4. ELECTRICAL CONNECTION ELECTRIC SHOCK HAZARD Disconnect power to the junction box before making connection Electrically ground the appliance with green or green-yellow colored wire Do not ground to a gas pipe Check with a qualified electricial if you are not sure that the range is grounded Do not have a fuse in the neutral or ground circuit WARNING - - FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DEATH, FIRE OR ELECTRICAL SHOCK. [. . . ] Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. If it will not fit in the outlet, have a proper outlet installed by a qualified electrician. - Refer to picture 1, where local codes allow the connection of the applliance's ground wire to the branch circuit neutral wire (white colored wire): The ground wire must be connceted first; If local codes permit, connect the green or yellow-green ground wire from the appliance and the white wire from the appliance to the branch circuit neutral wire (white colored wire). Connect the red and gray leads from the cooktop to the junction to the corresponding leads in the junction box. [. . . ]