User manual SMEG S45VCX2

[. . . ] The manufacturer will not assume any liability for damage caused by tests according to standards which are not listed in the declaration of conformity . Note Since we continuously improve our products we reserve all rights to modify these operating instructions and the functions described therein. We make all possible efforts to keep these instructions free of errors and complete. If you note any errors or unclear points please advise us. GB 2 9. 696. 037 ENGLISH S45VCX2 Before Starting 3 Guide to these Operating Instructions This chapter contains information on the functions of the machine and instructions for handling and installation. [. . . ] Before Starting BE SURE TO READ! Basic Functions Adjustment and operation of the machine are explained here. Troubleshooting and Maintenance Instructions for finding causes of malfunctions and eliminating them. This chapter includes information on the required maintenance, parts subject to wear and replacement parts. Technical Data Shows the interrelationship between various item numbers, the circuit and diagram plans and machine specifications. Intended Use The S45VCX2 machine is intended for commercial and industrial applications and should be used only for the intended purpose. The S45VCX2 machine is a sealing machine for sealing sterilization packages consisting of paper, paper laminate foil or Tyvek foil. !It is not suitable for sealing pure polyethylene foils, soft PVC foils, hard PVC foils, polyamide foils or polypropylene foils. The machine capacity depends on the characteristics of the sealing material used. 9. 696. 037 GB 3 ENGLISH S45VCX2 Before Starting 3 Set-Up and Function Power switch Power fuse Power connection Adjustable for the user manual Peel edge adjustment 5 - 30 mm Display Input and function keys Sealing and Printing Operation Sequence 1. The sterilization package is then transported and the area of the sealing seam is heated to the sealing temperature set on the upper and lower heating dies. The printing operation is activated and the activated print data is printed onto the sealed package. The finished sterilization package is transported to the discharge side. If more packages to be sealed are not fed in the transport mechanism shuts off after approx. Replace control board Display board Control board GB 14 9. 696. 037 ENGLISH S45VCX2 Troubleshooting and Maintenance 5 Maintenance Chart As all technical equipment your equipment is also subject to technical wear. In order to ensure that your machine is always ready for use it should be serviced at least once annually by a trained technician. Check Replace PTFE strip for guide die PTFE strip for sealing die Adjust Measure Sealing temperature between sealing die Maintenance chart Ink ribbon Pressure roller Toothed belt Sealing die interval At least every 3 months Depending on use, at least once annualy Parts Service F Simply order parts by fax: l Please copy the following pages according to the parts required. Page 17: Parts required for maintenance and wear Page 18: Replacement parts l Enter machine number. l Enter machine model l Enter name, address, fax number and order number. l Open housing l Remove mounting screws Œ for upper guide rail and remove guide rail. Œ l Remove pressure spring • l Disconnect electrical connections for heating die l Unscrew mounting srew • and remove spacer l Remove top or bottom heating die l Unscrew mounting screw ‘ and detach PTFE strip Œ l Remove backing foil on new PTFE strip and glue newe PTFE strip on straight and without wrinkels l Fasten PTFE strip with screw ‘ l Install heating die l Insert spacer and fasten with mounting screws • • l Reconnect electrical connections to heating die l Install pressure spring • • ‘ Œ l Install guide rails. ‘ FWhen installing the upper guide rail before fastening , push the die down so that the interval between the srew head and rail is 1mm on both sides. This ensures the correct contact pressure for the guide rail Distance between screw head and rail = 1mm l Close housing 9. 696. 037 GB 21 ENGLISH S45VCX2 Troubleshooting and Maintenance 5 Maintenance Information Replacing pressure roller !Please use only genuine replacement parts. l Switch off machine and DISCONNET POWER PLUG !l Open housing l Remove mounting screws Œ for upper guide rail and remove guide rail. l Loosen mounting screw Ž and pull pressure roller completely out of holder l Detach snap ring • and remove pressure roller l Install new pressure roller and fasten with snap ring • l Position complete pressure roller in holder, center in relation to bottom roller and tighten mounting screw Ž Ž Œ Œ Œ • l Install guide rail FWhen installing the upper guide rail before fastening, push the die down so that the interval between the screw head and rail is 1 mm on both sides. [. . . ] l Loosen mounting screw Ž and pull pressure roller completely out of holder l Detach snap ring • and remove pressure roller l Install new pressure roller and fasten with snap ring • l Position complete pressure roller in holder, center in relation to bottom roller and tighten mounting screw Ž Ž Œ Œ Œ • l Install guide rail FWhen installing the upper guide rail before fastening, push the die down so that the interval between the screw head and rail is 1 mm on both sides. This ensures the correct contact pressure for the guide rail. Distance between screw head and rail = 1 mm l Close housing GB 22 9. 696. 037 ENGLISH S45VCX2 Troubleshooting and Maintenance 5 Calibration After replacing the temperature sensor or heating elements it is necessary to calibrate the temperature. After replacing the print head or "print start" light barrier it is necessary to calibrate the printer. After replacing the electronic unit it is necessary to perform both adjustment operations. [. . . ]