User manual SMEG SE2622ID

[. . . ] IN YOUR OWN INTEREST, AND THAT OF SAFETY, IT IS THE LAW THAT ALL GAS AND ELECTRICAL APPLIANCES BE INSTALLED AND SERVICED BY COMPETENT PERSONS, WHO WILL COMPLY WITH THE RELEVANT STANDARDS AND REGULATIONS. SMEG REGISTERED INSTALLERS UNDERTAKE TO WORK TO SATISFCTIORY STANDARDS. DISCONNECTION OF GAS AND ELECTRIC APPLIANCES SHOULD ALWAYS BE CARRIED OUT BY COMPETENT PERSONS THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE HOB. [. . . ] HOB IGNITION OVAL COOKING ZONE CONTROLS ON-OFF REAR RIGHT-HAND COOKING ZONE VALUE INCREASE BUTTON FRONT RIGHT-HAND COOKING ZONE VALUE DECREASE BUTTON FRONT CENTRAL COOKING ZONE TIMER SETTING BUTTON FRONT LEFT-HAND COOKING ZONE DUAL COOKING ZONE REAR LEFT-HAND COOKING ZONE TRIPLE COOKING ZONE REAR CENTRAL COOKING ZONE HEATING ZONE (MOD. SE2958TC) CENTRAL COOKING ZONE SWITCHING ON THE HEATING ZONE (MOD. USE OF THE COOKING HOB 7. 1 Hobs with knobs 7. 1. 1 Single cooking zones Each knob shows the cooking zone it is for. identifies the knob that For example, the symbol controls the rear right-hand cooking zone. Adjustment is continuous so that the appliance also operates at any intermediate value. identifies the knob that controls the rear right-hand For example, the symbol cooking zone. To heat the inner cooking zone, turn the knob to the desired position (1 to 6). and then To heat both the inner and outer cooking zones, turn the knob to release. To adjust heating intensity, rotate the knob anticlockwise to the desired position. To return to heating of the inner cooking zone only, set the knob back to 0 and then turn to the desired position (1 to 6). 7. 1. 3 Description of symbols REAR LEFT FRONT LEFT REAR RIGHT FRONT RIGHT 7. 1. 4 Residual heat The 4 warning lights located between the cooking zones come on when the temperature of one or more of the zones exceeds 60°C. To use the timed cooking, first set the power level by following the instructions given in paragraphs "7. 2. 2 Single Cooking Zones" and "7. 2. 3 Dual Cooking Zones". key to enable the functions), press Now, with the hob NOT locked out (if it is locked out, press the the symbol . Between the symbols and of the first active cooking zone, a LED light will turn on to indicate that the minutes to be set will refer to operation of that particular zone. The automatic operation minutes of the cooking zone can be increased or decreased by using the and keys beside . After 5 seconds have gone by since the last time it is pressed, the timer will start and the cooking zone reaches 0. will operate until the display above the symbol At this point the cooking zone will automatically turn off. It is also possible to use the timed cooking function on more than cooking zone at the same time. key to shift the timer controls over to the next active Once the timer is set on the first zone, press zone (the LED light between the symbols and of the second active cooking zone will be activated) and then set the cooking duration as previously described. When the timed cooking is active on several cooking zones at the same time, the display between the and of the cooking zone will alternatively turn on and at the same time the minutes symbols display found on the symbol will show the time remaining for the zone with the LED light on. 7. 2. 9 Modifying the data set and symbols increases or reduces the power During timed cooking, each single pressure on the of the cooking zone. key until the LED light in the cooking To change the remaining time of a zone, you have to press zone turns on. [. . . ] Use a larger pan Check the instructions for timer Timed cooking programming error 28 Instructions for the installer 10. INSTALLATION 10. 1 Technical information See rating plate 220-240V~ 50/60Hz / 380-415V 2N 50/60Hz / 380-415V 3N 50/60Hz Electric See rating plate 290 510 595 510 720 510 900 510 Hob type Electrical connections HOB RATING Maximum electrical power DIMENSIONS OF THE HOB Width (mm) Depth (mm) 10. 2 The rating plate Make sure that the voltage and capacity of the power line conform to the data shown on the plate located under the casing. Do not remove this plate for any reason. . MODEL Serial N° 10. 3 Electrical connection IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE GROUNDED ACCORDING TO THE METHODS REQUIRED BY SAFETY RULES. WHEN LINKING UP TO MAINS BY PLUG AND SOCKET, MAKE SURE THAT BOTH ARE COMPATIBLE AND CONNECT BY MEANS OF A POWER CABLE COMPLYING WITH APPLICABLE REGULATIONS. [. . . ]