User manual SMEG SPR864AGH

[. . . ] • Never leave high naked flames under the hood when it is in operation. • Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides. • Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames. • Do not flambè under the range hood; risk of fire • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. [. . . ] • “ CAUTION: Accessible parts may become hot when used with cooking appliances. ”. MAINTENANCE • Switch off or unplug the appliance from the mains supply before carrying out any maintenance work. • Clean and/or replace the Filters after the specified time period (Fire hazard). • Clean the hood using a damp cloth and a neutral liquid detergent. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. EN 1 12 CHARACTERISTICS Dimensions 890 Min. 11a Q. ty Product components 1 Hood Body complete with: Controls, Light, Suction Unit, Filters, Lower Duct 1 PVC Pipe (fitted) 1 Inclinable grid (fitted) 1 Reduction flange ø 150-120 mm 1 Metal cover Q. ty Assembly components 2 SB 12/10 Plugs Q. ty Documents 1 Instruction Manual 10 8 11a 7 9 EN 1 13 INSTALLATION Boring the wall If you want to use the hood in suction version with the air outlet at the back of the hood, make sure to follow the indications given below in the drawing for a correct boring operation of the air outlet opening. Type Hood X 45 180 60 240 90 390 X 300 X 11a 540 650 mm min When installing the hood in recycling version it has to be taken into consideration that space remaining between the hood and the upper limit (ceiling or self) is at least 8-10 cm. On the wall, trace: • a vertical line up to the ceiling or top limit, at the centre of the area where you intend to fit the hood; • a horizontal line at: (650-550) mm min. above the cooking hob; • As shown, mark a reference point at 808 mm above the horizontal reference line, and at X mm (X= see table in figure) to the right of the vertical reference line. • Repeat this operation on the opposite side, checking levelling. After 200 working hours all the LEDs (L1-L2-L3-L4) will light up and start to flash to indicate saturation of the activated charcoal filters. Press and hold for approximately 5 seconds, with all the 2 flashes, Remote control Enabled. loads turned off (Motor and Lights), to enable/disable 1 flash, Remote control Disabled. At the end of this time the system will automatically return to the speed set before. Press and hold for approximately 5 seconds to 2 Flashes of the Leds (L1-L2-L3) enable/disable the Activated Charcoal Filter alarm. On. EN 1 17 MAINTENANCE Cleaning the Comfort Panels • Pull the Comfort Panel to open it. • Disconnect the panel from the hood canopy by sliding the fixing pin lever. • Clean the outside by using a damp cloth and neutral liquid detergent. • Clean the inside as well by using a damp cloth and neutral detergent; do not use wet cloths or sponges, or jets of water; do not use abrasive substances. • When the above operation has been completed, hook the panel back to the hood canopy and close it by turning the knob in the opposite direction. Metal grease filters These can also be washed in the dishwasher, and need to be cleaned when all the command LEDs light up in a continuous manner or at least once every 2 months use, or more frequently if use is particularly intensive. [. . . ] Resetting the alarm signal • Press button T1 (see the paragraph on Use). • Remove the Filters one at a time, pushing them towards the back of the unit and at the same time pulling downward. • Wash the Filters without bending them, and leave them to dry completely before replacing. • Replace, taking care to ensure that the handle faces forwards • Close the comfort panels. EN 1 18 Activated Charcoal Filter (Recirculation Version) • This cannot be washed or regenerated, and must be changed when all the command LEDs start to flash, or at least once every 4 months. [. . . ]