User manual SMEG ST732L

[. . . ] We advise you to carefully read all the instructions contained in this manual, in order to understand how to operate your dishwasher safely and correctly. The manual is divided into paragraphs, which provide a step by step description of the dishwasher functions, with clear instructions accompanied by detailed illustrations. Recommendations are given for the correct use of the baskets, spray arms, containers, filters, washing programs, and for operating the controls. Follow the recommended cleaning procedures to ensure that your dishwasher always remains in perfect working order. [. . . ] Then proceed to select the program in the manner described previously: the dishwasher will immediately perform a pre-wash cycle, and then automatically initiate the countdown of the delayed start programmed; the INFORMATION DISPLAY (4) will show a blinking clock symbol and the time remaining to the start of the program. AND PROTECT THE ENVIRONMENT Always try to run the dishwasher fully loaded. · Use the washing program that is most appropriate for each type of load. · If available, connect the dishwasher to a hot water supply up to 60°C. · When possible, disable the drying cycle and leave the door open at the end of the washing · cycle: the residual air and heat will dry the dishes perfectly. AND PROTECT THE ENVIRONMENT The phosphates contained in dishwasher detergents are harmful to the environment. To avoid using excessive amounts of detergent and to save on electricity, observe the following: · separate the more delicate items from dishes that are more resistant to aggressive detergents and high temperatures; · do not pour the detergent directly on the dishes. REMOVING THE DISHES At the end of the washing program, wait at least 20 minutes before removing the dishes, to allow them to cool down. To prevent any water droplets on the upper basket from falling on the dishes in the lower basket, it is advisable to unload the lower basket first, and then the upper basket. 32 User instructions 4. Operating instructions Once the dishwasher has been correctly installed, prepare for use as follows: Adjust the water softening system; · Add the regenerating salt; · Add the rinse aid and detergent. · 4. 1 Using the water softening system The amount of scale contained in the water (water hardness index) can cause whitish staining on the dry dishes, which tend to become dull over time. Then use a screwdriver to rotate the rinse aid selector to the desired position. The amount of rinse aid must be increased if the washed dishes appear dull or feature circular stains. If, on the other hand, the dishes are sticky or have white streaks, it is necessary to reduce the rinse aid setting. 35 User instructions ADDING THE DETERGENT To open the detergent dispenser cap, lightly press the button P. During the washing cycle, the dispenser will be opened automatically. · When a SUPER program is selected, in addition to the normal dose of detergent, it is necessary to add an additional amount inside compartment G or H. For optimal washing results it is important to use a good quality detergent. The detergent packs must be sealed and stored in a dry place to prevent the formation of lumps which may negatively affect washing results. Once opened the detergent packs should not be kept for too long, otherwise the detergent loses its effectiveness. Do not use detergents formulated for washing dishes by hand, because they produce a great deal of foam and may negatively affect the operation of the dishwasher. An insufficient amount of detergent will result in a partial removal of dirt from the dishes, whereas an excessive amount is wasteful and does not improve the washing results. There are various types of detergents available on the market - liquid, powder and tablet forms - characterised by different chemical compositions: some contain phosphates, whereas others are phosphate free and based on natural enzymes. - Detergents containing phosphates are more effective against grease and starch at temperatures above 60°C. [. . . ] Wash the arms under a jet of running water and return them carefully to their seat. Otherwise, check that they have been installed correctly. 41 User instructions CLEANING THE FILTER UNIT It is advisable to periodically inspect the centre filter C and, if necessary, to clean it. To remove · the filter, grip the tabs, turn them anticlockwise and lift upwards; push the centre filter D from the underside to remove it from the micro-filter: · separate the two parts which make up the plastic filter by pressing the body of the filter in the · zone shown by the arrows; remove the centre filter by lifting it upwards. · GENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT MAINTENANCE: · · · The filters should be cleaned under running water using a stiff brush. [. . . ]