User manual TOSHIBA ET1

[. . . ] OWNER’S MANUAL 3LCD PROJECTOR TLP-ET1B TLP-ET1E TLP-ET1U Others Maintenance Operations Preparations Before Using English Before Using SAFETY PRECAUTIONS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (ser vicing) instructions in the literature accompanying the appliance. WARNING: Handling the cord on this product or cords associated with accessories sold with this product, will expose you to lead, a chemical known to the State of California to cause birth defects or other USA only reproductive harm. FCC Radio Frequency Interference Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, USA only pursuant to part 15 of the FCC Rules. [. . . ] Front/Rear Lamp power Notes • “Projection size” can also be adjusted by using ( ) and ( ) buttons, on the remote control or main unit. ) (See • Decreasing the projection size may affect image quality slightly. ) • “Picture mode” can also be set via the PICTURE MODE button on the remote control or the “Picture adjustp. (See • “Screen size” can also be set via the SIZE button on the remote control or the “Default setting” menu. ) • “Keystone”, “Up/down shift”, “Lamp power”, and “Projection mode 1” can also be adjusted via the “Default setting” menu. ) • The items set and adjusted on the “Easy setting” menu are saved when the power is turned off with the ON/ STANDBY button. They are not saved if power is disconnected by unplugging the power cord or by a power failure. 20) is used to change the projection angle, the picture will undergo keystone (trapezoid) distortion. Before correction After correction • Depending on the amount of keystone adjustment and the content of images, some information may be lost or the picture quality may suffer. 23 Others Maintenance Operations Preparations Projection mode 1 Before Using English Operations Changing the projection size You can change the projection size (picture area size on the screen). Remote control Control panel Notes • The “Projection size” can also be adjusted via the “Easy setting” menu. ) • Decreasing the projection size may degrade the images more or less. 24 Operations The projection screen of this projector is 16:9, though the screen size can be changed depending on the input signal. Pressing the SIZE button for the first time displays the current screen size. Pressing the SIZE button while the current screen size is displayed cycles the screen size through the following options: Full → Theater wide → 4:3 → Zoom Full : This mode is best for squeeze-signal video images. Theater wide : This mode is best for 4:3-signal video images on the wide screen. 4:3 : This mode is best for 4:3-signal video images on the 4:3size screen. zoom : This mode is best for video images of letter-box or cinema signals. Input signal 4:3 signal Full Projection screen Theater wide (O) → Zoom 4:3 signal ← Squeeze signal Full (O) Theater wide → Zoom Notes • The screen size cannot be changed when the 16:9 signal is input. € You cannot select “Theater wide” and “Zoom” when the input is COMPUTER. € An adjustment bar of “Up/ down shift” is displayed in “Zoom” mode and you can make the adjustment (See p. ) • If you use this function on commercial video software or on a broadcast or cable broadcast except for the purpose of your private viewing and listening, it may infringe the copyright protected by the copyright laws. [. . . ] One minute of abnormal display, the projector returns to the standby state waiting for internal cool down. One minute of abnormal display, the projector returns to the standby state waiting for internal cool down. (Red lit) (Orange flashing) (Green lit) PRECAUTIONS • Make sure to unplug the power cord if something goes wrong. € If the power cord is unplugged before cooling is complete, give the lamp enough time to cool before plugging it back in. [. . . ]