User manual TOSHIBA RBC-AMT32E INSTALLATION MANUAL

[. . . ] 10 1-4-1 Application for indoor remote controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 1-4-2 Two remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1-4-3 Group control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 1-4-4 Application controls for central remote controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Use the provided cord clips to fasten the remote controller cord to the wall. Reattach the nameplate. If the separate receiver unit is installed on the ceiling, use the provided ceiling mounting bracket for installation. Insert a screwdriver or similar tool into the notch at the bottom to remove the receiver nameplate. Cut a section out of the ceiling along the provided paper pattern (95 x 51 mm). Pass the wire through the provided mounting bracket and insert the bracket into the installation hole. (Refer to "Wiring the Receiver Unit. ") Check the terminal number on the indoor unit before wiring the receiver unit and be sure not to wire incorrectly. (The unit will be damaged if high voltage, such as 200 VAC, is applied. ) 6. Adjust the provided spacers so that they are several millimeters larger than the thickness of the ceiling material. Pass the 2 supplied screws (M4 x 40) through the spacers and tighten them enough to hold the receiver unit in place. Part (A) Part (B) Fig. E 7. Return parts (A) and (B) through the gap between the ceiling and receiver unit so that they are contained in the openings. Tighten to the point where the receiver unit can be moved slightly by hand. While this display is flashing, the model is being automatically confirmed. Accordingly, wait for 1 minute after [SET DATA] display has disappeared, and then use the remote controller. Display section ADR ADR Operation section SET CL ACL SENSOR 1 2 3 ADR 5 7 9 10 6 8 4 1 2 3 Transmitting indication Displayed while operating the switches of the remote controller. (AUTO) (HIGH) (MED. ) (LOW) Filter display If "FILTER " is displayed, clean the air filter. CHECK display Displayed while the protective device works or a trouble occurs. 6 7 8 9 Set up temperature display The selected set up temp. Flap position display SWING display Displayed during up/down movement of the flap. (When a trouble occurs, the check code is displayed. ) Timer SETIN setup display When pushing the Timer SET button, the display of the timer is selected in order of [OFF] [OFF] repeat OFF timer [ON] No display. 10 4 5 83 Operation Section Push each button to select a desired operation. · The details of the operation needs to be set up once, afterward, the air conditioner can be used by pushing button only. 1 2 3 ADR 5 6 SET CL 4 ACL SENSOR 7 1 2 3 4 5 Operation select button Selects desired operation mode. Set required set temperature by pushing 6 Start/Stop button When the button is pushed, operation starts, and it stops by pushing the button again. When the operation stops, the operation lamp and all displays disappear. Filter reset button Resets (Erases) "FILTER " display. 7 OPTION : or . Remote controller sensor Usually the TEMP. For details, contact the dealer from which you have purchased the air conditioner. 84 Signal Receiving Part (TCB-AX21U(W)-E) · The signal receiving part is mounted to the ceiling panel. Signal Receiving Part 10 2 8 9 4 3 1 4 5 2 3 N O 1 4 3 2 N O 1 N O 03 S0 7 03 S0 N O 1 2 3 4 5 6 Emergency operation button Signal receiving part The signal sent from the remote controller is received. [. . . ] · In case of central control among 1:1 models, be sure to set SW01-1 to ON in the system with the least line address number. Cabling connection of control wiring Attach an adapter per 1 group in group control operation (including individual control). Connect the adapter to the header indoor unit in the group control. Central control devices Indoor unit U3 U4 TCB-PCNT 30TLE (Adapter) Indoor control P. C. board A B central control wiring Indoor unit Indoor unit U3 U4 TCB-PCNT 30TLE (Adapter) Indoor control P. C. [. . . ]