User manual TOYOTA SUPERJ15WE
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual TOYOTA SUPERJ15WE. We hope that this TOYOTA SUPERJ15WE user guide will be useful to you.
You may also download the following manuals related to this product:
TOYOTA SUPERJ15WE (2123 ko)
TOYOTA SUPERJ15WE (2123 ko)
TOYOTA SUPERJ15WE (2114 ko)
TOYOTA SUPERJ15WE (2150 ko)
TOYOTA SUPERJ15WE (2124 ko)
TOYOTA SUPERJ15WE (2132 ko)
Manual abstract: user guide TOYOTA SUPERJ15WE
Detailed instructions for use are in the User's Guide.
[. . . ] SP100 Series
HOME-USE SEWING MACHINE
•• Read this manual carefully before use and always follow the instructions. •• Keep the manual in a convenient place for easy reference. •• If you give the sewing machine to someone else, also give them this instruction manual.
INSTRUCTION MANUAL
Contents
1
Before use (Be sure to read this section before use)
•• •• •• •• •• •• Important safety instructions. 3 How to change the power plug. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Guide Hook
2Turn
20
zz Using the needle threader
1
While fully lowering the needle threader lever, hook the thread on the guide as shown in the diagram.
Needle threader lever Guide
2
Sewing preparations
2
Fully turn the needle threader lever to the rear, and pull the thread through the needle threader slot.
Needle threader slot 1 Slowly return the needle threader lever towards yourself as much as possible. 3 Release the needle threader lever while releasing the end of the thread. ** If the needle is not threaded, check that the needle has been raised to its highest position, and then repeat the procedure starting with step 1 .
Pull the thread loop that formed behind the needle, and then pull about 15 cm of thread to the rear.
15 cm
21
Pulling up the lower thread
1
Raise the presser foot lever. Loosely hold the upper thread with your left hand, and then turn the handwheel towards yourself one full turn. Do not pull the thread taut.
2
Lightly pull the upper thread with your left hand to pull up the lower thread.
Pull out the lower thread to the front.
Align both threads, pass them through the groove (arrow) and under the presser foot, and then pull out about 15 cm of thread to the rear.
Presser foot 15 cm
22
Application of each stitch pattern
Caution
Before turning the pattern selection dial, use the main power switch to turn off the sewing machine. Not doing so could cause an injury.
Caution
Do not turn the pattern selection dial while the needle is lowered. Doing so could break the needle and cause an injury.
2
Sewing preparations
Turn the handwheel towards yourself to raise the needle in the highest position. Turn the pattern selection dial to choose the pattern.
Pattern selection dial
Buttonhole
Blind hem stitch
Zigzag Applique Overcasting Straight stitch Sewing-seams Zipper insertion
Scallop stitch
Castle stitch
Thin fabric straight stitch
Decorative stitch Fagotting
Mending stitch Thin fabric overcasting
Decorative stitch Serpentine
23
Changing the presser foot
Caution
Before changing the presser foot, use the main power switch to turn off the sewing machine. Not doing so could cause an injury.
zz Removal
1
Raise the presser foot lever.
2
Turn the handwheel towards yourself to raise the needle. Handwheel
Presser foot lever
Press the presser foot holder lever in the direction of the arrow to release the presser foot.
Presser foot holder lever
Presser foot
24
zz Installation
1
Position the presser foot pin directly below the groove in the presser foot holder.
Presser foot holder
2
Groove
Sewing preparations
Presser foot pin
2
Lower the presser foot lever to secure the presser foot.
Presser foot lever
Tip
In order to avoid losing the presser foot, we recommend storing the machine when it is not being used with the needle and the presser foot lowered.
25
Changing the needle
Caution
Before changing the needle, use the main power switch to turn off the sewing machine. Not doing so could cause an injury.
1 2
Turn the handwheel towards yourself to raise the point of the needle higher than the needle plate. Hold the needle in one hand, loosen the needle clamp screw with the screw driver for the needle plate, and remove the needle. Face the flat surface of the needle to the rear and insert until it makes contact with the pin. Firmly tighten the needle clamp screw with the screw driver for the needle plate. Pin
Screw driver for the needle plate
Needle clamp screw
Flat surface
zz Correct needle selection
Good needle
If a faulty needle is used, not only could it impair the sewing performance, but it could also damage the needle plate or hook, or break the needle. ** Incorrect stitching or thread breaking, try replacing the needle.
ÍFaulty needle
The entire needle is bent
26
The point of the needle is crushed / worn away
The point of the needle is bent
Relationship between the needle, thread and fabric, and adjusting the thread tension
The quality of the sewing finish will improve if the needle and thread are changed to match the type of fabric. 50 Curtains Denim Quilting Fleece Tweed Felt, etc.
2
Sewing preparations
Thread
Fabric
Normal front cloth Broad Soft denim Satin Pile Gingham, etc.
-2
-1
+2 +1
+2
+3
+4
Upper thread tension dial
-1 ~ -3
+1 ~ +3
zzFor XXX15D/ SuperJ15
-2 -3
-1 ~ -3
-1 ~ +3
• Use a ball point needle for the sewing alignment of stretch fabric. • Please purchase any needles not included as accessories, after checking they are specified as home-use sewing machine needles. • The bigger the needle number is , the thicker the needle is, the bigger the thread number is, the thinner the thread is. • Normally, sew with the upper thread tension dial set to “ XXX15D/SuperJ15). ” (for XXX15C) / “ ” (for
27
+
1
+
-
1
-1
3
+2 +1
3
Sewing
Caution
Do not pull the fabric excessively while sewing. Doing so could break the needle and cause an injury.
Straight stitching and reverse sewing
zz Straight stitch 1
1 2
Turn the handwheel towards yourself to raise the needle. [. . . ] If this occurs, remove the needle plate and bobbin case, and attach them again.
4
Maintenance 45
Changing light bulb
Warning
Before changing the light bulb, use the main power switch to turn off the sewing machine, remove the power plug from the outlet, and then wait until the bulb cools. Not doing so could cause a burn or electric shock.
8 1
Loosen the screw with a + screw driver of your own, and take off the face cover in the direction of the arrow.
Screw
Face cover
8 2
Turn the light bulb counterclockwise as the arrow in the diagram and remove.
Turn the new light bulb clockwise to install. Always reinstall the face cover after replacing the light bulb.
46
Servicing double-insulated products (230V-240V)
In a double-insulated product, two systems of insulation are provided instead of grounding. No grounding means are provided on a double-insulated product nor should a means for grounding be added to the product. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE TOYOTA SUPERJ15WE
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual TOYOTA SUPERJ15WE will begin.