User manual VDO ENGINE ACTUATORS BROCHURE

[. . . ] Do not attach any seal, label or data protection sheet to either side of a disc. NEVER insert a 3-inch CD contained in the adapter or an irregularly shaped CD. Disc can not have foreign body, the damage caused by the disc with foreign body do not belong to the warranty scope. Before Operation Do not raise the volume level too much, as this will block outside sounds, making driving dangerous. Stop the car before performing any complicated operation. CAUTION DO NOT open covers and do not repair yoursel f . [. . . ] Stop the car before performing any complicated operation. CAUTION DO NOT open covers and do not repair yoursel f . In addition to ordinary CDs, this unit can playback CD - R or CD - RW, MP3. Note: The system just support the english and number display , other letter can't display or display * 2 ENGINE ACTUATORS CD PLAYBACK Panel Controls Panel Controls (1) (2) Disc eject Rotate to adjust volume. Radio:mute CD/MP3:Pause Hold it to power off (3) EQ setup button (4) 1-6 Preset automatically search station (5) channel 1/random play (6) channel 2/ intro play (10 sec. ) (7) channel 3/repeat play (8) channel 4 (9) channel 5/MP3 folder back (10) Channel6/mp3 folder ahead (11) Display paly time and clock in the CDstate. Turn and turn about folder name/file name / ID3 TAG/system time Display PTY info and system time in the Radio state. (12) Band select (13) USB connector (14) Select previous track (15) Select next track (16) Disc slot (17) SCR key Radio Disc play(when disc is in) USB(when USB inserted) AUX IN (18) Reset hole (19) Press to select VOL/BAS/TRE/BAL/LOUD/ FAD/AF/TA/PTY, Rotate VOL knob to adjust RADIO: Rotate to adjust radio tune CD /MP3: Rotate to select track the previous /next (20) 1-6 Preset: Press to tune in a preset station. Hold for more than 2 seconds to store station. © Continental Trading GmbH 3 Operate guide Operate guide Disc Load / Eject Load : Insert the disc into the slot. Eject: Press to eject the disc . EQ LOUD mode Press [EQ] button setting to sound effect POP CLASSIC - ROCK - JAZZ EQ - OFF Press [TUNE]-knob to setting VOL / BAS / TRE / BAL / FAD / LOUD / AF / TA / PTY, Rotate [VOL]knob to adjust value. Mp3 Track Search USB/MP3 mode: Press [AST] knob to select "TRK SCH" mode. The desired track number Press the [TUNE]-knob to switch first digit and tenth digit, Rotate the [VOL]knob to adjust the first digit and press the [TUNE]knob to confirm. also to the setting tenth digit and hundredth digit of the track number. BAND mode Press the button [FM/AM] to change BAND. FM1x FM2 - FM3 - MW1 - MW2 Clock setting On the radio mode: Press [DSP] to display PTY info/ time. When playing a disc of 8kbps or VBR1, the elapsed playing time in the display window will not be correct and also the intro play may not function properly. Note on creating your own CD-Rs or CD-RWs containing MP3 files To enjoy high quality sound, we recommend converting to MP3 files with a sampling frequency of 44. 1 kHz and a fixed bit rate of 128 kbps. For ISO 9660 -compliant format, the maximum allowable depth of nested folders is 8, including the root directory (folder). When CD-R disc is used, playback is possible only for discs which have been finalized. Make sure that when MP3 CD-R or CDRW is burned that it is formatted as a data disc and NOT as an audio disc. You should not write non-MP3 files or unneeded folders along with MP3 files on the disc otherwise it takes a long time until the unit starts to play MP3 files. With some CD-R or CD-RW media, data may not be properly written depending on their manufacturing quality . Up to 16 characters are displayed for the name of an Album or a Track. Note that the unit may not play Track in the order that you wrote them to the disc. USB Notes USB functions (flash memory type) MP3 music play USB flash memory 2 in 1 support FAT 12 / FAT 16 / FAT 32 format supported. USB 1 . 1 support, USB 2. 0 support (For 2. 0, speed performance is as USB 1. 1) Not all USB devices are compatible with the unit. Usb connector is support maximum work power with 500mA. 1. VBR: Variable Bit Rate © Continental Trading GmbH 5 Electrical Connections Electrical Connections Wiring Diagram Location A1 A2 A3 A4 A5 A6 A7 A8 No Function Function B1 B2 B3 B4 B5 B6 B7 B8 Location Rear R+ Rear RFront R+ Front RFront L+ Front LRear L+ Rear L- Function Telephone Mute High Telephine Mute Low Ignition Antenna remote Illumination Battery + Power Ground 6 ENGINE ACTUATORS CD PLAYBACK Troubleshooting Troubleshooting If you suspect something is wrong, immediately switch power off. [. . . ] Note that the unit may not play Track in the order that you wrote them to the disc. USB Notes USB functions (flash memory type) MP3 music play USB flash memory 2 in 1 support FAT 12 / FAT 16 / FAT 32 format supported. USB 1 . 1 support, USB 2. 0 support (For 2. 0, speed performance is as USB 1. 1) Not all USB devices are compatible with the unit. Usb connector is support maximum work power with 500mA. 1. VBR: Variable Bit Rate © Continental Trading GmbH 5 Electrical Connections Electrical Connections Wiring Diagram Location A1 A2 A3 A4 A5 A6 A7 A8 No Function Function B1 B2 B3 B4 B5 B6 B7 B8 Location Rear R+ Rear RFront R+ Front RFront L+ Front LRear L+ Rear L- Function Telephone Mute High Telephine Mute Low Ignition Antenna remote Illumination Battery + Power Ground 6 ENGINE ACTUATORS CD PLAYBACK Troubleshooting Troubleshooting If you suspect something is wrong, immediately switch power off. Do not use the unit in abnormal condition, for example without sound, or with smoke or foul smell, can cause fire or electric Option General No power or no sound Car's engine switch is not on Car's engine switch is not on Volume is too low If the above solutions cannot help Disc Disc is inside but is no sound Disc is upside down Disc is dirty or damaged Disc sound is skips, tone quality is low Radio Much noise in broadcasts Preset station lost Error Display Messages CD ERR Disc is upside down Disc format is not support or file date is wrong Place disc in the correct direction, and the label side up check the disc Station is too far, or signals are too weak Battery cable is not correctly connected Select other stations of higher signal level Connect the battery cable to the terminal that is always live. [. . . ]